Product Documentation and Knowledge Base - HomeDocumentation


Charon-VAXCharon-AXPCharon-PDPCharon-SSPCharon-PAR

PCI I/O Bypass controller

Owned by Kirill Nikolaev (Unlicensed)
Last updated: May 07, 2018
5 min read

Table of Contents

Back to Table of Contents

General description

CHARON-AXP supports PCI I/O bypass controller for accessing to disk images and host physical disks. PCI I/O bypass controller requires a specific driver to be installed.

PCI I/O bypass controller support is available only for OpenVMS guest operating system.

Back to Table of Contents

Prerequisites

This release supports VMS version V6.2-1H3 and higher. Bypass disks can not be used as a boot device in V6.2-1H3, higher versions do not have this restriction.

Make sure that the latest Bypass controller kit has been installed, especially for VMS versions before V7.3-2.

Back to Table of Contents

Installation

  1. Open your VM configuration and attach the virtual disk "ovms_tool.vdisk"  located by default in the "C:\Program Files\CHARON\Virtual Disk Images\OpenVMS tools package" directory:

    set PKA container[400] = "C:\Program Files\CHARON\Virtual Disk Images\OpenVMS tools package\ovms_tools.vdisk"
  2. Run VM, boot guest OpenVMS operating system.

  3. Use the POLYCENTER Software Installation (PCSI) utility to install the Bypass Driver.  The following example demonstrates the "PCSI PRODUCT INSTALL" command to execute and the expected output (the example assumes the utilities virtual disk image is attached as DKA400:):

    $ PRODUCT INSTALL CHARON_DISK/SOURCE=DKA400:[BYPASS]
    %PCSI-I-CANNOTVAL, cannot validate DKA400:[BYPASS]SRI-AXPVMS-CHARON_DISK-V0104--1.PCSI;1
    -PCSI-I-NOTSIGNED, product kit is not signed and therefore has no manifest file
     
    The following product has been selected:
        SRI AXPVMS CHARON_DISK V1.4 Layered Product
     
    Do you want to continue? [YES] YES
     
    Configuration phase starting ...
     
    You will be asked to choose options, if any, for each selected product and for any products that may be installed to satisfy software dependency requirements.
     
    SRI AXPVMS CHARON_DISK V1.4: Charon disk driver V1.4 for OpenVMS Alpha.
     
        Copyright (C) 1976, 2009 Software Resources International
     
        CHARON_DISK was produced by Software Resources International
     
    * This product does not have any configuration options.
     
    Execution phase starting ...
     
    The following product will be installed to destination:
        SRI AXPVMS CHARON_DISK V1.4 DISK$TARDISSYSTEM:[VMS$COMMON.]
     
    Portion done: 0%...10%...20%...80%...100%
     
    The following product has been installed:
        SRI AXPVMS CHARON_DISK V1.4 Layered Product

Back to Table of Contents

Loading PCI I/O bypass controller

Syntax for loading PCI I/O bypass storage adapter:

load pci_io_bypass <name>

The <name> can be DI<x>, DR<x> or DU<x>

where x is selected according to VMS naming scheme, i.e. A stands for the first controller of given type, B - for the second, etc.

Example:

load pci_io_bypass DIA


In AlphaStation 400 configuration use the following syntax for PCI I/O bypass storage loading:

load pci_io_bypass DIA irq_bus = isa

The adapter instance name ("DIA" in the example above) is used then for parametrization, for example:

set DIA container[0]="C:\My disks\vms_distribution.vdisk"

The numbers in the square brackets represent a number of device on PCI I/O Bypass controller.

The maximum number of I/O Bypass controller devices is 64.

By default I/O Bypass controller uses PCI slot corresponded to the <x> parameter (see above). If instead some particular slot is needed, refer to this section for details of specific placement of PCI peripherals on CHARON Virtual Machine (VM) PCI bus (note that "irq_bus" and "irq" parameters are ignored for I/O Bypass controller). In this case the <x> will be changed automatically according to custom position of I/O Bypass controller on PCI bus.

(info) I/O Bypass controller is implemented for OpenVMS only.

Back to Table of Contents

Configuration parameters

The I/O Bypass controller has the following configuration parameters:

container

Parameter

container[N]

N is 0..32766 (no more than 64 units)

TypeText string
Value

Possible values of the parameter are strings in one of the following forms:

  • Physical disk

    •  "\\.\PhysicalDrive<X>", where X is 0, 1, … 
      (warning) Be careful not to destroy all the information from the disk dedicated to CHARON VM by mistake. 
      These disks must not be formatted by the host OS. 
      Example:

      set DIA container[0]="\\.\PhysicalDrive1"

      .

  • Physical disk by its WWID 

    • "\\.\PhysicalDrive(DevID=XXX-...-XXXX)"

      (warning) Be careful not to destroy all the information from the disk dedicated to CHARON VM by mistake.

      These disks must not be formatted by the host OS.

      DevID addresses the target physical disk by its WWID (hexadecimal 128-bit identifier assigned to the disk drive by its manufacturer/originator).

      Example:

      set DIA container[100]="\\.\PhysicalDrive(DevID=6008-05F3-0005-2950-BF8E-0B86-A0C7-0001)"

      .

  • iSCSI disks
    • "\\.\PhysicalDrive(iScsiTarget = <iSCSI target>, LUN = <LUN number>)"

      iScsiTarget addresses the disk by its iSCSI target name.

      LUN specifies LUN on connected iSCSI disk.

      Example:

      set DIA container[200]="\\.\PhysicalDrive(iScsiTarget=iqn.2008-04:iscsi.charon-target-test1, LUN= 1)"

      .

  • File representing a physical disk of the HP Alpha system (disk image)

    • [<drive>":\"<path-name>"\"]<file-name>[".vdisk"] 
      These files can be created from scratch with "MkDisk" utility. Data and OS disks backups are transferred from the original system via tapes or network and restored into these container files.   
      Mapping may also include the full path (recommended), for example: "C:\My disks\my_boot_disk.vdisk"   
      Example: 

      set DIA container[401]="tru64-v51-system.vdisk"

      Using compressed folders to store virtual disks and tapes is not supported

      .

  • Other type of drive, for example magneto-optical drive

    • "\\.\<N>:" 
      Example:

      set DIA container[300]="\\.\Z:"

      Using compressed folders to store virtual disks and tapes is not supported

      .

(info) This parameter is initially not set, thus creating NO storage elements on the controller..

removable

Parameter

removable[N]

N is 0..32766 (no more than 64 units)

TypeBoolean
Value

When set to "true", the removable configuration parameter instructs CHARON VM to report the corresponding virtual disk as removable.

Note to set this parameter to "true" if this disk storage element is:

  • Mapped to a host removable device
  • Mapped to a disk image located on a host removable device
  • Mapped to a disk image that has to be renamed/moved/deleted right after dismounting it in the guest OS

By default the removable configuration parameter is set to "false".

Example:

set DIA removable[400]=true

geometry

Parameter

geometry [N] 

N is 0..32766 (no more than 64 units)

TypeText String
Value

This formatted string value specifies the explicit geometry of the disk storage element. This parameter is not applicable to tape storage elements.

The string format is ”*/*/*/<B>" or ”*,*,*<B>" where B is the total size of the disk (in blocks) reported to the guest OS. If omitted it is calculated automatically.

If this parameter is not set, CHARON VM will configure the geometry based on the most probable disk type.

Initially not set.

use_io_file_buffering

Parameter

use_io_file_buffering[N]

N is 0..32766 (no more than 64 units)

TypeText String
Value

Instructs CHARON VM to enable host operating system I/O cache on reading/writing operations.

The following values are possible:

  • "true" or "write-back" - the "write back" caching mode is used

  • "write-through" - the "write through" caching mode is used

  • "false" - caching is switched off

(info) Note that this caching has a significant effect only in case of mapping to disk and tape containers, not physical drives.

When enabled, host operating system I/O cache may significantly improve I/O performance of the virtual system. At the same time maintaining I/O cache requires additional host resources (CPU and memory) which may negatively affect overall performance of the virtual system.

Initially is set to "false".

Example:

set DIA use_io_file_buffering[603]=true


When a disk image connected to an I/O Bypass controller is dismounted by OpenVMS, it is disconnected from CHARON VM and can be manipulated. It can be replaced with a different disk image if it keeps the same name. This capability may be useful when designing back-up and restore procedures. When copying CHARON-AXP disk images while CHARON VM is running, please take care to minimize the risk of overloading a heavily loaded CHARON host system. For example, using a sequential series of simple ftp binary copies is less resource intensive and thus less disruptive than multiple, simultaneous copies.

Empty disk images are created with the "MkDisk" utility.

CHARON-AXP is able to boot from disk images of any OpenVMS/Alpha version.

Back to Table of Contents

Deinstallation

  1. Do a conversational boot. Please refer to your OpenVMS system administration guide for instructions.
  2. Set the NOAUTOCONFIG system parameter to 1
  3. Boot OpenVMS
  4. Remove the product with the "$ PRODUCT REMOVE CHARON_DISK" command.
  5. Set the NOAUTOCONFIG system parameter to 0 and reboot.   


Back to Table of Contents


© Stromasys, 1999-2024  - All the information is provided on the best effort basis, and might be changed anytime without notice. Information provided does not mean Stromasys commitment to any features described.