Table of Contents

Introduction

This section describes how to migrate your HP Alpha system to CHARON-AXP. We will use a sample HP AlphaServer ES40 system running OpenVMS to demonstrate the migration procedure. The process is similar for all CHARON-AXP models.

Back to Table of Contents

Collecting information about the source HP Alpha system

The first step is to determine the exact configuration of your HP Alpha hardware in order to create the CHARON-AXP configuration file.

Turn on your source HP Alpha system. At the ">>>" prompt, issue "show device" command:

>>>show device

sys0.0.0.0.0 SYS0 System ROOT Device
ewa0.0.0.1.1 EWA0 F8-D1-11-00-67-E6
pka0.0.0.2.1 PKA0 Q-Logic/ISP PCI SCSI HBA
pga0.0.0.3.1 PGA0 WWN 1000-0000-0248-C550
pqa0.0.0.15.0 PQA0 ALi 1553C Integrated IDE Controller
pqb0.0.1.15.0 PQB0 ALi 1553C Integrated IDE Controller
dqa0.0.0.15.0 DQA0 TSSTcorpCDDVDW SH-222BB
dka0.0.0.2.1 DKA0 DEC RZ28 (C)DEC
dka100.1.0.2.1 DKA100 DEC RZ22 (C)DEC
dka200.2.0.2.1 DKA200 DEC RZ23 (C)DEC
mka600.6.0.2.1 MKA600 Virtual SCSI Tape

>>>

To get more detailed information boot OpenVMS and issue "show dev /full" command:

$ show device /full

Disk PFCAXP$DKA0:, device type RZ28, is online, mounted, file-oriented device,
 shareable, available to cluster, error logging is enabled.
...

Disk PFCAXP$DKA100:, device type RZ22, is online, file-oriented device,
 shareable, available to cluster, error logging is enabled.
...

Disk PFCAXP$DKA200:, device type RZ23, is online, file-oriented device,
 shareable, available to cluster, error logging is enabled.
...

Disk PFCAXP$DQA0:, device type TSSTcorpCDDVDW SH-222BB, is online, file-oriented
 device, shareable, available to cluster, error logging is enabled.
...

Disk $1$DGA0: (PFCAXP), device type RZ24, is online, file-oriented device,
 shareable, available to cluster, error logging is enabled.
...

Magtape PFCAXP$MKA600:, device type Virtual SCSI Tape, is online, file-oriented
 device, available to cluster, error logging is enabled, device supports
 fastskip (per_io).
...

Terminal OPA0:, device type VT102, is online, record-oriented device, carriage
 control.
...

Device EWA0:, device type DE500, is online, network device, device is a template
 only.
...

Device FGA0:, device type KGPSA Fibre Channel, is online, shareable, error
 logging is enabled.
...

Device PGA0:, device type SCSI FCP, is online, error logging is enabled.

...

Device PKA0:, device type Qlogic ISP1020 SCSI port, is online, error logging is
 enabled.
...

Device $1$GGA32767:, device type Generic SCSI device, is online, shareable.

$

In case of Tru64 UNIX V5 running on the host system it is recommended to use the following commands to get information on the host configuration:

Command	Description
`#/sbin/hwmgr view devices`	Get detailed information about the host hardware configuration
`#/sbin/hwmgr show scsi`	Get specific information about the host SCSI controllers and attached disks
`#/sbin/hwmgr view hierarchy`	Get information about the host controllers

Please reference to the Tru64 UNIX User's Guide for more details.

The source HP Alpha peripheral configuration in this example is:

Controller	Devices on controller	Description
KZPBA	-DKA0 (RZ28) -DKA100 (RZ22) -DKA200 (RZ23) -MKA600 (tape)	SCSI disk/tape controller
KGPSA-CA	-DGA0 (RZ24)	FC disk controller
OPA0		System console
TSSTcorpCDDVDW SH-222BB	-DQA0	IDE CD-ROM controller
EWA0		Network interface, MAC address: "F8-D1-11-00-67-E6"

Now collect some general information about the HP AlphaServer ES40 system:

>>>show cpu /full

System: PFCAXP, AlphaServer ES40 6/667

SMP execlet = 3 : Enabled : Streamlined.
Config tree = None
Primary CPU = 0
HWRPB CPUs = 4
Page Size = 8192
Revision Code =
Serial Number = SN01234567
Default CPU Capabilities:
System: QUORUM RUN
Default Process Capabilities:
System: QUORUM RUN

....

>>>

>>>show mem

System Memory Resources on 5-FEB-2015 09:29:16.42

Physical Memory Usage (pages): Total Free In Use Modified
Main Memory (512.00MB) 65536 56496 8610 430

...

>>>

So the collected information about the HP AlphaServer ES40 system is:

Component	Value
System Type	AlphaServer ES40 6/667
Serial Number	SN01234567
Number of CPUs	4
System memory	512 Mb

In some particular situations it is also important to know the exact placement of all the peripheral devices on HP Alpha PCI bus. To get that information issue "show config" command at ">>>" prompt of HP Alpha console, for example:

>>>show config

...

PCI Bus

Bus 00 Slot 03: DECchip 21142 Network Controller
ewa0.0.0.3.0 00-00-F8-03-9A-6D

Bus 00 Slot 07: Cypress PCI Peripheral Controller

Bus 00 Slot 07: Function 1: PCI IDE

Bus 00 Slot 07: Function 2: PCI IDE

Bus 00 Slot 07: PCI USB

Bus 00 Slot 08: DECchip 21052 PCI to PCI Bridge

Bus 01 Slot 08: ISP1040 Scsi Controller
pka0.7.0.1008.0 SCSI Bus ID 7
dka0.0.0.1008.0 RZ2DD-KS
dka400.4.0.1008.0 RRD45

>>>

The "show config" command collects the following information of placement of peripheral devices on PCI bus:

Bus number
Slot number
Function number

To find out the exact types of controllers and other useful information refer to the source HP Alpha system documentation.

Back to Table of Contents

Creation of CHARON-AXP configuration file

Using the above info, the following configuration can be created:

#
# HP AlphaServer model: AlphaServer ES40 6/667
#

set session hw_model = AlphaServer_ES40
set ace cpu_architecture = EV67
set rom dsrdb[0] = 1820 system_name = "AlphaServer ES40 6/667"

...

#
# Override default System Serial Number, set it to "SN01234567"
#

set rom system_serial_number = SN01234567

#
# Specify RAM size: 512 Mb
#

set ram size=512

#
# Map OPA0 console to "Putty" terminal emulator (included in CHARON-AXP kit)
#

load virtual_serial_line OPA0 port=10003 application="putty -load OPA0"

#
# Сonnect the emulator's DQA0 to the host's ATAPI CD/DVD-ROM drive.
#

set ide container="\\.\CdRom0"

#
# Load optional DE500BA PCI Ethernet Adapter (EWA0) and map it to the "Charon" host network interface
#

load DE500BA/dec21x4x EWA interface=EWA0
load packet_port/chnetwrk EWA0 interface="connection:Charon"

#
# Load DEC-KZPBA SCSI controller and map it to 3 disk containers and 1 tape container
#

load KZPBA PKA scsi_id = 7

set PKA container[0] = "C:\My disks\bootable.vdisk"
set PKA container[100] = "C:\My disks\RZ22.vdisk"
set PKA container[200] = "C:\My disks\RZ23.vdisk"

set PKA container[600] = "C:\My tapes\my_tape.vtape"

#
# Load DEC-KGPSA-CA PCI FC adapter and map it to a disk container
#

load KGPSA FGA

set FGA container[0] = "C:\My disks\RZ24.vdisk"

...

Back to Table of Contents

Making disk images

In our example, possible mappings of KZPBA SCSI controller include disk and tape images. Tape images have not to be manually created whereas you have to provision disk images, as described below.

Our example creates disk images of the original physical type. In reality, this step is the best opportunity in the migration to provision bigger disks to get extra storage space.

Create special directories for storing disk and tape images, as needed. Created directories are referenced in the sample configuration file above.

...> cd C:

\
C:\> mkdir "My disks"

C:\> mkdir "My tapes"

This operation can also be done using Windows Explorer.

Start the "MkDisk" utility from the "Start" menu to create disk images:

The main dialog of the utility will appear:

Select "Alpha AXP" in the "Select System" drop-down menu, "SCSI" in the "All Controllers" drop-down menu and "RZ24" (for example) in the "Select Disk Type" drop-down menu.

Press then the "Create Disk Image" button:

The utility will ask you to specify the output file name. Select the "C:\My disks" directory created just before (or create it directly in the dialog) and press "Save" button:

The "MkDisk" utility will create the requested disk image:

Repeat this sequence for the disks "RZ28.vdisk", "RZ22.vdisk" and "RZ23.vdisk". Place them in the same folder.

Back to Table of Contents

Installation of HP Alpha operating system

The next step is to transfer the data from the source HP Alpha system to CHARON-AXP. The easiest way to do this is via backup over the network. But for this operation we need a bootable, network-enabled operating system on a CHARON-AXP disk image or physical disk.

The example configures the CHARON-AXP AlphaServer ES40 system for installation of HP OpenVMS from a distribution CD-ROM (usually it is "\\.\CdRom0" if the host has only one CD-ROM drive):

# # DEC-KZPBA SCSI controller is mapped to 5 disk containers; one of them (DKA300) - for migration purposes; # another one (DKA400) - for installation of fresh HP OpenVMS system from distributive
#

load KZPBA PKA scsi_id = 7

set PKA container[0] = "C:\My disks\bootable.vdisk"
set PKA container[100] = "C:\My disks\RZ22.vdisk"
set PKA container[200] = "C:\My disks\RZ23.vdisk" set PKA container[300] = "C:\My disks\migration.vdisk" set PKA container[400] = "C:\My disks\fresh_openvms.vdisk"

#
# CD-ROM for HP OpenVMS installation (DQA0)
#

set ide container="\\.\CdRom0"

DKA300 will be the disk where all the source disks will be copied, so its size needs to be big enough to store all the disk backup images

Create an empty disk image for installation of HP OpenVMS and another one for storing backups from the source HP Alpha system as it is shown in the section above.

Run CHARON-AXP and boot from the CDROM named "dqa0" ("migration.cfg" is the configuration file we use in this example):

...>es40.exe migration.cfg

CHARON-AXP/ES40 for Windows x64 (AlphaServer ES40 6/667), Version 4.6.16603
(C) 2009-2014 STROMASYS SA.
All rights reserved.

P00>>>boot dqa0

Install HP Alpha/VMS including DECnet on "dka400". DECnet address must belong to the same area as the source HP Alpha system.

Login to the newly installed OpenVMS system and initialize the disk intended for backups storage. Let's assume it's prompt is "newvms$ "

newvms$ INIT DKA300: SCRATCH
newvms$ MOUNT/SYSTEM/NOASSIST DKA300: SCRATCH

Back to Table of Contents

Making remote backups

Now we are ready to create disk backups from the source HP Alpha system to CHARON-AXP.

Boot CHARON-AXP and make sure that the source HP Alpha system is available via DECnet.

Login to the source HP Alpha system. Stop all the batch queues, kick off the users, stop all application and close databases if any. The commands listed in SYS$MANAGER:SYSHUTDWN.COM may be helpful. The goal is to close as many files as possible. The system disk will have several files opened (pagefile, swapfile, etc.), but this is normal.

The use of the "SHOW DEVICE /FILES" command would be of help to know files opened on a disk

Let's assume the CHARON-AXP system is node 1.400 in this example. Issue then the following commands from the source HP Alpha whose prompt is set to "source$ "

source$ BACKUP/IMAGE/IGNORE=INTERLOCK DKA0: 1.400::DKA300:[000000]DKA0.BCK/SAVE
source$BACKUP/IMAGE/IGNORE=INTERLOCK DKA100: 1.400::DKA300:[000000]DKA100.BCK/SAVEsource$ BACKUP/IMAGE/IGNORE=INTERLOCK DKA200: 1.400::DKA300:[000000]DKA200.BCK/SAVE

Once the backup procedure completes, the disk "DKA300" of CHARON-AXP will contain 3 savesets: "DKA0.BCK", "DKA100.BCK" and "DKA200.BCK"

Back to Table of Contents

Restore backups to CHARON-AXP disks

Next, restore the new savesets to their corresponding virtual disks. Login to CHARON-AXP and issue this sequence of commands to restore all the savesets created on the previous step:

newvms$ MOUNT/FOREIGN DKA0:
newvms$ BACKUP/IMAGE DKA300:[000000]DKA0.BCK/SAVE DKA0:
newvms$ DISMOUNT DKA0:

newvms$ MOUNT/FOREIGN DKA100:
newvms$ BACKUP/IMAGE DKA300:[000000]DKA100.BCK/SAVE DKA100:
newvms$ DISMOUNT DKA100:

newvms$ MOUNT/FOREIGN DKA200:
newvms$ BACKUP/IMAGE DKA300:[000000]DKA200.BCK/SAVE DKA200:
newvms$ DISMOUNT DKA200:

If you are going to have CHARON-AXP and the original physical HP Alpha on the network at the same time, you must change the network identity of one (usually the CHARON-AXP).

The easiest way is to boot the CHARON-AXP virtualized system on the restored system disk with the network Disabled and configure new addresses, as needed. The NIC can be disabled with a "connection:disabled" statement in the CHARON configuration file.

Then Enable the network and reboot.

Back to Table of Contents

Alternative ways of data transfer

Some alternative methods of data transfer are also possible. For example:

Connect a SCSI tape drive to CHARON-AXP host via a PCI card
- Map the tape drive in the CHARON-AXP configuration file
  a. Restore source HP Alpha system backups from tape to disk images via OpenVMS running on CHARON-AXP.
  b. Boot from standalone backups and restore its content to CHARON-AXP virtual disks
- Dump source HP Alpha system backups to tape images with "mtd" utility and:
  a. Boot from freshly installed OpenVMS system and restore the tape images to CHARON-AXP virtual disks
  b. Boot from standalone backups and restore its content to CHARON-AXP virtual disks
Create a network cluster between the source HP Alpha system and CHARON-AXP (it is possible to use the source system as boot server); then simple backup from one disk to another:
$ BACKUP/IMAGE/IGNORE=INTERLOCK REAL$DKA0: DKA0:

Back to Table of Contents

Browser not supported