VAX 6610 configuration file

VAX 6610 configuration file

#
# Copyright (C) 1999-2014 STROMASYS
# All rights reserved.
#
# The software contained on this media is proprietary to and embodies
# the confidential technology of STROMASYS. Possession, use, duplication,
# or dissemination of the software and media is authorized only pursuant
# to a valid written license from STROMASYS.
#
#============================================================================
#
# Sample configuration file for VAX 6000 Model 610.
#
#----------------------------------------------------------------------------

set session hw_model = VAX_6610

#============================================================================
#
# Choose a name for the instance, if needed, to differentiate it among other
# instances running on the same host.
#
#----------------------------------------------------------------------------

#set session configuration_name = VAX_6610

#============================================================================
#
# Use the following commands to disable the rotating LOG files and enable
# a single LOG file. Select either append or overwrite (for each time the
# instance starts) and specify desired log path and file name.
#
#----------------------------------------------------------------------------

#set session log_method = append
#set session log_method = overwrite
#set session log = VAX_6610.log

#============================================================================
#
# To enable automatic boot, define the default boot device in the VAX
# console and uncomment the line below.
#
#----------------------------------------------------------------------------

#set xmi boot = auto

#============================================================================
#
# The following line tells the emulator where to preserve NVRAM content.
# The TOY file maintains the current time of the emulated VAX (when it is not
# running) and other console parameters (such as default boot device).
#
# Both files must be enabled to correctly preserve the saved state of the console.
#
#----------------------------------------------------------------------------

#set toy container = "charon.dat"
#set eeprom container = "charon.rom"

#============================================================================
#
# Specify the size of RAM (default 32MB). Note that DIT (when enabled)
# also needs certain amount of memory which grows linearly following
# the size of memory specified here. Also remember that the dongle
# license might limit the maximum amount of memory.
#
# The valid settings are: 32,64,128,256,512,768,1024, ... 3072,
#
#----------------------------------------------------------------------------

#set ram size = 512
#set ram size = 768
#set ram size = 1024
#set ram size = 2048
#set ram size = 3584

#============================================================================
#
# Select the connection method for the console serial line OPA0.
#
#----------------------------------------------------------------------------

#load physical_serial_line OPA0 line = "/dev/tty<N>"
#load virtual_serial_line OPA0 port = 10003
load operator_console OPA0

#----------------------------------------------------------------------------
#
# Uncomment to allow 'F6' to terminate the running emulator.
#
#----------------------------------------------------------------------------

#set OPA0 stop_on = F6

#============================================================================
#
# Uncomment to enable emulation of KDM70 storage controller.
#
#----------------------------------------------------------------------------

#load KDM70 PUA xmi_node_id = 11

#============================================================================
#
# Uncomment to connect the emulator's DUA0 to the disk image.
#
#----------------------------------------------------------------------------

#set PUA container[0] = "<file-name>.vdisk"

#============================================================================
#
# Uncomment to connect the emulator's DUA100 to a host disk drive.
#
#----------------------------------------------------------------------------

#set PUA container[100] = "/dev/sd<L>"

#============================================================================
#
# Uncomment to connect the emulator's DUA300 to the host's CD/DVD-ROM drive.
#
# Device name may be different depending on particular version of host
# operating system. Choose one which suits best.
#
#----------------------------------------------------------------------------

#set PUA container[300] = "/dev/cdrom"
#set PUA container[300] = "/dev/cdrom1"
#set PUA container[300] = "/dev/cdrom<N>"
#set PUA container[300] = "/dev/sr0"
#set PUA container[300] = "/dev/sr<N>"

#============================================================================
#
# Uncomment to connect the emulator's DUA400 to an .ISO file (CD/DVD image).
#
#----------------------------------------------------------------------------

#set PUA container[400] = "<file-name>.iso"

#============================================================================
#
# Uncomment to connect the emulator's MUA600 to a .VTAPE file (tape image).
#
#----------------------------------------------------------------------------

#set PUA container[600] = "<file-name>.vtape"

#============================================================================
#
# Support of CI:
#
# Load CIXCD adapter into slot 12 (C) of the XMI.
#
#----------------------------------------------------------------------------

#load CIXCD PAA xmi_node_id = 12 ci_node_id = 0x01

#============================================================================
#
# Support of CI:
#
# Connect HSJ50 storage controller to the CIXCD adapter PAA.
#
#----------------------------------------------------------------------------

#load HSJ50 PUA ci_node_id = 0x0B mscp_allocation_class = 1

#============================================================================
#
# Uncomment to connect the emulator's DUA0 to the disk image.
#
#----------------------------------------------------------------------------

#set PUA container[0] = "<file-name>.vdisk"

#============================================================================
#
# Uncomment to connect the emulator's DUA100 to a host disk drive.
#
#----------------------------------------------------------------------------

#set PUA container[100] = "/dev/sd<L>"

#============================================================================
#
# DEMNA XMI Ethernet Adapter EXA
#
#----------------------------------------------------------------------------

#load DEMNA EXA xmi_node_id = 13 interface = EXA0
#load packet_port EXA0 interface = "(disabled)"
#set EXA0 interface = "eth<N>"

#============================================================================
#
# DEMNA XMI Ethernet Adapter EXB
#
#----------------------------------------------------------------------------

#load DEMNA EXB xmi_node_id = 14 interface = EXB0
#load packet_port EXB0 interface = "(disabled)"
#set EXB0 interface = "eth<N>"

# this is the end of the configuration file ##################################

Back to Top