## Copyright (C) 1999-2017 STROMASYS# All rights reserved.## The software contained on this media is proprietary to and embodies# the confidential technology of STROMASYS. Possession, use, duplication,# or dissemination of the software and media is authorized only pursuant# to a valid written license from STROMASYS.##============================================================================## Sample configuration file for VAX 6000 Model 610.##----------------------------------------------------------------------------
set session hw_model = VAX_6610
#============================================================================## Choose a name for the instance, if needed, to differentiate it among other# instances running on the same host.##----------------------------------------------------------------------------
#set session configuration_name = VAX_6610
#============================================================================## Use the following commands to disable the rotating LOG files and enable# a single LOG file. Select either append or overwrite (for each time the# instance starts) and specify desired log path and file name.##----------------------------------------------------------------------------
set session log_method = append#set session log_method = overwrite#set session log = VAX_6610.log
#============================================================================## To enable automatic boot, define the default boot device in the VAX # console and uncomment the line below.##----------------------------------------------------------------------------
#set xmi boot = auto
#============================================================================## The following line tells the emulator where to preserve NVRAM content.# The TOY file maintains the current time of the emulated VAX (when it is not# running) and other console parameters (such as default boot device).## Both files must be enabled to correctly preserve the console settings.##----------------------------------------------------------------------------
#set toy container = "charon.dat"#set eeprom container = "charon.rom"
#============================================================================## Specify the size of RAM (default 512MB). Note that DIT (when enabled)# also needs certain amount of memory which grows linearly following# the size of memory specified here. Also remember that the dongle# license might limit the maximum amount of memory.## The valid settings are: 32,64,128,256,512,768,1024, ... 3584, ##----------------------------------------------------------------------------
#set ram size = 512#set ram size = 768#set ram size = 1024#set ram size = 2048#set ram size = 3584
#============================================================================## Select the connection method for the console serial line OPA0.##----------------------------------------------------------------------------
#load physical_serial_line OPA0 line = "/dev/tty<N>"#load virtual_serial_line OPA0 port = 10003load operator_console OPA0
#----------------------------------------------------------------------------## Uncomment to allow 'F6' to terminate the running emulator.##----------------------------------------------------------------------------
#set OPA0 stop_on = "F6"
#============================================================================## Uncomment to enable emulation of KDM70 storage controller.##----------------------------------------------------------------------------
#load KDM70 PUA xmi_node_id = 11
#============================================================================## Uncomment to connect the emulator's DUA0 to a .VDISK file (disk image).##----------------------------------------------------------------------------
#set PUA container[0] = "<file-name>.vdisk"
#============================================================================## Uncomment to connect the emulator's DUA1 to a host disk drive.##----------------------------------------------------------------------------
#set PUA container[1] = "/dev/sd<L>"
#============================================================================## Uncomment to connect the emulator's DUA3 to an .ISO file (CD/DVD image).##----------------------------------------------------------------------------
#set PUA container[3] = "<file-name>.iso"
#============================================================================## Uncomment to connect the emulator's DUA4 to the host's CD/DVD-ROM drive.## Device name may be different depending on particular version of host# operating system. Choose one which suits best.##----------------------------------------------------------------------------
#set PUA container[4] = "/dev/cdrom"#set PUA container[4] = "/dev/cdrom1"#set PUA container[4] = "/dev/cdrom<N>"#set PUA container[4] = "/dev/sr0"#set PUA container[4] = "/dev/sr<N>"
#============================================================================## Uncomment to connect the emulator's MUA5 to a .VTAPE file (tape image).##----------------------------------------------------------------------------
#set PUA container[5] = "<file-name>.vtape"
#============================================================================## Support of CI:## Load CIXCD adapter into slot 12 (C) of the XMI.##----------------------------------------------------------------------------
#load CIXCD PAA xmi_node_id = 12 ci_node_id = 0x01
#============================================================================## Support of CI:## Connect HSJ50 storage controller to the CIXCD adapter PAA.##----------------------------------------------------------------------------
#load HSJ50 PUA ci_node_id = 0x0B mscp_allocation_class = 1
#============================================================================## Uncomment to connect the emulator's DUA0 to the disk image.##----------------------------------------------------------------------------
#set PUA container[0] = "<file-name>.vdisk"
#============================================================================## Uncomment to connect the emulator's DUA1 to a host disk drive.##----------------------------------------------------------------------------
#set PUA container[1] = "/dev/sd<L>"
#============================================================================## DEMNA XMI Ethernet Adapter EXA.## Uncomment both lines to enable emulation of EXA.##----------------------------------------------------------------------------
#load DEMNA EXA xmi_node_id = 13 interface = EXA0#load packet_port EXA0 interface = "(disabled)"
#----------------------------------------------------------------------------## Connect EXA0 to a host NIC.##----------------------------------------------------------------------------
#set EXA0 interface = "eth<N>"
#============================================================================## DEMNA XMI Ethernet Adapter EXB.## Uncomment both lines to enable emulation of EXB.##----------------------------------------------------------------------------
#load DEMNA EXB xmi_node_id = 14 interface = EXB0#load packet_port EXB0 interface = "(disabled)"
#----------------------------------------------------------------------------## Connect EXB0 to a host NIC.##----------------------------------------------------------------------------
#set EXB0 interface = "eth<N>"
# this is the end of the configuration file ##################################