## Copyright (C) 1999-2014 STROMASYS# All rights reserved.## The software contained on this media is proprietary to and embodies# the confidential technology of STROMASYS. Possession, use, duplication,# or dissemination of the software and media is authorized only pursuant# to a valid written license from STROMASYS.#
## Sample configuration file for:## * Charon-VAX/6610## Emulator of the VAX model:## * VAX 6610#set session hw_model = VAX_6610
#============================================================================## Choose a name for the instance, if needed, to differentiate it among other# instances running on the same host.##----------------------------------------------------------------------------
#set session configuration_name = VAX_6610
#============================================================================## Use the following commands to disable the rotating LOG files and enable# a single LOG file. Select either append or overwrite (for each time the# instance starts) and specify desired log path and file name.##----------------------------------------------------------------------------
#set session log_method = append#set session log_method = overwrite#set session log = VAX_6610.log
## To enable automatic boot, define the default boot device in the VAX # console and uncomment the line below.#
#set xmi boot=auto
## TOY date/time, boot options, ...#
set toy container="vx6k610.dat"
## EEPROM settings, e.g. default boot drive#
set eeprom container="vx6k610.rom"
### Specify the size of RAM (default 32MB). Note that DIT (when enabled)# also needs certain amount of memory which grows linearly following# the size of memory specified here. Also remember that the dongle# license might limit the maximum amount of memory.## The valid settings are: 32,64,128,256,512,768,1024, ... 3584,
# 32bit systems only: Please note, that to be able to run the ~2Gb # (2048) of simulated memory you should enable /3GB switch#
set ram size=512#set ram size=768#set ram size=1024#set ram size=2048#set ram size=3584
## Now assign built-in console serial line. Currently the emulator# offers two possible ways of using built-in serial lines. First of# them is to attach a third party terminal emulator (virtual_serial_line).# The second is connection to COM ports (via physical_serial_line).## Once the way of the connection is defined corresponding mapping# to the host resources can be performed.## Connection to a third party terminal emulator:#
load virtual_serial_line/chserial OPA0#set OPA0 port=10003 application="opa0.ht"set OPA0 port=10003 application="putty.exe -load OPA0"#set OPA0 port=10003 application="c:\kea\user\opa0.ktc"
## Connection to a physical COM port of the host:#
# load physical_serial_line/chserial OPA0# set OPA0 line="COM1:"
## Load the MSCP controller with the name DUA#
load KDM70/KDM70 DUA xmi_node_id=11
## Map the storage units for loaded MSCP controller DUA.## In VMS, the DUA0 will correspond to the 'DUA container[0]', etc...## Examples:## set DUA container[0]="C:\Disk-Images\charon-6000\dua0.vdisk"# set DUA container[1]="\\.\PhysicalDrive1"# set DUA container[2]="\\.\CdRom0"# set DUA container[3]="\\.\A:"## It is also possible to map a tape drive identified by the host# operating system to the DUA controller.# # Example:# # set DUA container[3]="\\.\Tape0"#
#set DUA container[0]="..."
## Support of CI:# Load CIXCD adapter into slot 12 (C) of the XMI.#
#load CIXCD PAA xmi_node_id=12 ci_node_id=0x01
## Support of CI:# Connect HSJ50 controller to the CIXCD adapter PAA.#
#load HSJ50 PUA ci_node_id=0x0B mscp_allocation_class=1
## Map the storage units for the loaded HSJ50 controller PUA.## In VMS, the PUA will correspond to the 'DUA container[0]', etc...## Examples:## set PUA container[0]="C:\Disk-Images\charon-6000\dua0.vdisk"# set PUA container[1]="\\.\PhysicalDrive1"# set PUA container[2]="\\.\CdRom0"# set PUA container[3]="\\.\A:"## It is also possible to map a tape drive identified by the host# operating system to the PUA controller.# # Example:# # set PUA container[3]="\\.\Tape0"#
#set PUA container[0]="..."
## IMPORTANT NOTE:## Make sure that DUA and PUA do not conflict in the VMS environment, since # the disks on those controllers have the same name "DUA[x]" preceded by # their allocation class (for the HSJ50 controller it is set in the # configuration file). Assign the allocation class in such a way to avoid # name conflicts or enable only either DUA or PUA.## See CHARON-66x0 User Guide for more details.#
## Load Ethernet Controllers## 2 Ethernet controllers are loaded in this sample configuration file: EXA# and EXB. Both of them are connected to corresponding network interfaces:# EXA_0 and EXB_0. The initial settings for the interfaces are "disabled".# The exact mapping to the host ethernet interfaces will be defined later# in this configuration file.#
load DEMNA/demna EXA xmi_node_id=13 interface=EXA_0load packet_port/chnetwrk EXA_0 interface="(disabled)"
load DEMNA/demna EXB xmi_node_id=14 interface=EXB_0load packet_port/chnetwrk EXB_0 interface="(disabled)"
## Map the Network connections. ## Each connection is instantiated by the two objects. One is DEMNA controler# emulator EXn where n is A or B, and second is packet port EXn_0 where the# n is A or B.## In the emulated VMS, the network devices EXn will correspond to the # EXn, EXn_0 pair in the configuration file.## To assign the spesific permanent address to the desired EXn controller# ucomment the corresponding line below.## Example:## set EXA station_address="00-63-50-1A-A3-1E"#
#set EXA station_address="..."#set EXB station_address="..."
## To connect the corresponding adapter to the external device, uncomment# the line below and put the valid interface definition.## Example:## set EXA_0 interface="Cabletron DE500B PCI Fast Ethernet Adapter (21143-PC)"#
#set EXA_0 interface="connection:<connection-name>"#set EXB_0 interface="connection:<connection-name>"
# this is the end of the configuration file ##################################