...

Important Information to Protect the License Validity

Certain actions can invalidate your license. Therefore, once you have installed your license, please note the following points:

...

...

Perform the following basic steps to request and install a license:

• For the first license request in a VMware environment: use the esxi_bind command to bind the license server to its ESXi host or vCenter server.
• Collect the fingerprint (the customer-to-vendor - or C2V - file) on the license server and (if applicable) the backup license server.
• Send the fingerprint data to Stromasys stating license requirements based on your contract with Stromasys (product version, number of concurrent instances, is this the main or the backup license, etc.). Stromasys will send you the license data.
• Install the license data (the vendor-to-customer - or V2C - file) on the license server and (if applicable) on the backup license server.
• Verify the license installation.

These basic steps are described in more detail below.

Running the esxi_bind Command

The esxi_bind command sets up the necessary communication connection between the VE license server and the ESXi host / the vCenter server.

It must be run on the license server (and the backup license server, if applicable)

• once before the first license is requested,
• and again should the user for the access to the ESXi host / the vCenter server change.

Perform the following steps:

...

1. <user> is the user for interactive login associated with your license server system.
2. <license-server-ip> the ip address of your license server system.
   

...

1. Become the root user: # sudo -i
2. Run the c2v program: # /opt/license-server/esxi_bind -a <address> -u <username> -p <password>
where
   1. <address> is the IP address of the ESXi host or vCenter server.
   2. <username> is a user with administrative rights on the ESXi host or vCenter server.
   3. <password> is the password of the administrative user.

...

Overview - Requesting and Installing a License

License Installation Using the Command-Line

The following sections will show how to perform a license installation on the VE license server. Alternatively, you can use the web-based GUI (see VE License Server Web-based Management GUI)

Running the esxi_bind Command (VMware environment only)

Collecting the Fingerprint Data on the License Server

The fingerprint is collected on the license server using the c2v utility.

Perform the following steps to collect the fingerprint on the license server and (if applicable) the backup license server:

1. Use ssh to log in on the license server instance.
   # ssh -i ~/.ssh/<mykey> <user>@<license-server-ip>
   where
   1. <mykey> is the private key of the key-pair you associated with your cloud instance. For an on-premises VMware installation where login with username/password is allowed, it is not needed.
   2. <user> is the user for interactive login associated with your license server instance (e.g., opc on OCI, centos for a CentOS instance on AWS, or the custom user on your VMware virtual machine; for an instance installed from a prepackaged Charon-SSP VE marketplace image, use sshuser)
   3. <license-server-ip> is the ip address of your license server system.
      
2. Become the privileged user and run the c2v program.
   1. Become the root user: # sudo -i
   2. Run the c2v program: # /opt/license-server/c2v --filename <my-file>.c2v --platform <my-platform>
where
      1. <my-file>.c2v is the path and name under which you want to store the fingerprint. The file type is C2V (customer-to-vendor).
      2. <my-platform> indicates the platform on which the license server runs. Possible values: aws, oci, gcp, azure, ibm, or esxi.
3. Copy the resulting C2V file to your local system (unless you can send email from the license server system).

Sending the C2V File to Stromasys and Receive License Data File

Stromasys or your Stromasys VAR will provide you with an email address to which you should send the C2V file you created in the previous step.

In response, you will receive a so-called V2C (vendor-to-customer) file which contains the license data. The content of the license (type of emulated SPARC, expiration date, number of concurrent instances, etc.) depends on your contract with Stromasys. You may also receive a text file containing the license content in human readable form.

Installing the License Data on the License Server

The license data is installed on the license server using the v2c utility.

Perform the following steps to install the license on the license server:

...

1. <mykey> is the private key of the key-pair you associated with your license server instance. For an on-premises VMware installation where login with username/password is allowed, it is not needed.
2. <user> is the user for interactive login associated with your license server instance (e.g., opc on OCI, centos for a CentOS instance on AWS, or the custom user on your VMware virtual machine); for an instance installed from a prepackaged Charon-SSP VE marketplace image, use sshuser).
3. <license-server-ip> is the ip address of your license server system.
   

...

Verifying License Installation and License Content

Checking the License Server Log file

Check the license server log file to see if the server started successfully or reported an error. Use the following command (as the privileged user):
# cat /opt/license-server/

...

After the installation of the V2C file, the license server will be restarted.

Please note:

• Starting with version 1.0.35, a previously installed license will be cleanly removed once a new license is installed with the v2c command.
• In versions before 1.0.17, the license server will not start until a valid license has been installed.

The following example shows the installation of a V2C file:

$ sudo /opt/license-server/v2c -f mylicense.v2c 
<<V2C>> Going to import "mylicense.v2c" ...
<<V2C>> Imported "mylicense.v2c" successfully.
<<V2C>> Restarting license server ...
<<V2C>> Done

Verifying the License Installation

log/license.log

The log should indicate that the license server is ready to serve licenses.

Using the license_viewer Program to Display the Content of a License

The license server provides a license_viewer program to view the content of the license. To run it, use the following command (as the privileged user):

#/opt/license-server/license_viewer

The following sample shows the output of an active license:

...

...

table shows examples for several different license types and platforms (please note that the output may vary depending on platform and software version) :

...

...

...

Important product-specific license parameters:

• P_RLSD is the expiration date.

• P_MAJV and P_MINV are the major and minor product versions.

• P_CPU_NUM defines the maximum number of CPUs in an emulated SPARC system.

• P_MAX_MEM defines the maximum amount of RAM in an emulated SPARC system.

• P_INSTANCE defines the maximum number of concurrently running emulated SPARC systems.

Important key-specific license parameters:

• K_PLATFORM: the platform for which the license has been created.
• K_LICENSE_ID: in older versions, the license ID changed if the license server software was reinstalled; in newer versions, it will remain unchanged as long as the license server host instance is not re-installed.
• K_TYPE: possible values are NORMAL (time-limited or perpetual license) or COUNTDOWN (limited to a certain number of emulator runtime hours).
• K_EXPIRED: configured number of emulator runtime hours. The remaining hours can be seen in the web interface of the license server and the emulator log file.
• K_INTERVAL: configured license check interval.

...

Using the Web Interface

The license server provides a web interface to display important license characteristics and a list of currently connected client systems and emulator instances.

Prerequisite: access to TCP port 8084 of the license server must be possible.

The following image shows sample output of a backup license with 179 hours and 57 minutes of runtime remaining:

Image Removed

The following image shows sample output of a regular license with an expiration date and one client attached:

Image Removed

...

...

The license contains a key-specific section and one or more product-specific sections. Please note that the product-specific section is mostly not applicable to AutoVE licenses as this license is based on the number and configuration of the cloud-based host instances.

License Verification Using the Web Interface

See VE License Server Web-based Management GUI and Additional Configuration Options - the config.ini File for more information.