Page Comparison

Anchor

	TopPageTOCTopPage
	TOC

Include Page

	KBCOMMON:KB-CSSstyle
	KBCOMMON:KB-CSSstyle

#
# Copyright (C) 1999-2016 2018 STROMASYS
# All rights reserved.
#
# The software contained on this media is proprietary to and embodies the
# the confidential technology of STROMASYS. Possession, use, duplication, or
# or dissemination of the software and media is authorized only pursuant to a
# to a valid written license from STROMASYS.
#
#============================================================================
#
# Sample configuration file for VAX 4000 Model 108.
#
# Specify the hw_model prior to any other commands. This parameter informs
# the emulator what type of VAX it should build and enables all other
# commands.
#
#----------------------------------------------------------------------------

...

#load physical_serial_line /chserial TTA0 line="\\.\COMn"
#load virtual_serial_line /chserial TTA0 port=10000
#load virtual_serial_line /chserial TTA0 port=10000 application="tta0.ht"
#load virtual_serial_line /chserial TTA0 port=10000 application="putty.exe -load TTA0"
#set quart line[0]=TTA0

#load physical_serial_line /chserial TTA1 line="\\.\COM1"
#load virtual_serial_line /chserial TTA1 port=10001
#load virtual_serial_line /chserial TTA1 port=10001 application="tta1.ht"
#load virtual_serial_line /chserial TTA1 port=10001 application="putty.exe -load TTA1"
#set quart line[1]=TTA1

#load physical_serial_line /chserial TTA2 line="\\.\COM2"
#load virtual_serial_line /chserial TTA2 port=10002
#load virtual_serial_line /chserial TTA2 port=10002 application="tta2.ht"
#load virtual_serial_line /chserial TTA2 port=10002 application="putty.exe -load TTA2"
#set quart line[2]=TTA2

...

#load physical_serial_line /chserial OPA0 line="\\.\COM3"
#load virtual_serial_line /chserial OPA0 port=10003
#load virtual_serial_line /chserial OPA0 port=10003 application="opa0.ht"
load virtual_serial_line /chserial OPA0 port = 10003 application = "putty .exe -load OPA0 -P 10003"
set quart line[3]=OPA0

#============================================================================
#
# The VAX 4000 Model 108 contains built-in PCI SCSI adapter called PKA
# within the configuration file.
#
#-----------------------------------------------------------------------------------------------------
#
# Uncomment to connect the emulator's DKA0 to the disk imageallow 'F6' to terminate the running emulator. Closing console
# satellite application may also be used for that.
#
#----------------------------------------------------------------------------

#load virtual_scsi_disk pka_0 scsi_bus=pka scsi_id=0
#set pka_0 container="<file-name>.vdisk#set OPA0 stop_on = "F6"
#set OPA0 stop_on = "Application"
#set OPA0 stop_on = "F6, Application"

#============================================================================
#
# Uncomment to connect the emulator's DKA100 to a host disk driveThe VAX 4000 Model 108 contains built-in PCI SCSI adapter called PKA
# within the configuration file.
#
#----------------------------------------------------------------------------

#load virtual_scsi_disk pka_1 scsi_bus=pka scsi_id=1
#set pka_1 container="\\.\PhysicalDrive0"
#set pka_1 container="\\.\PhysicalDriveN"

#============================================================================-------
#
# Uncomment to connect the emulator's GKA200 to an unknown SCSI deviceDKA0 to the disk image.
#
#----------------------------------------------------------------------------

#load physicalvirtual_scsi_device disk pka_2 0 scsi_bus=pka scsi_id=20
#set pka_2 0 container="\\.\ScsiN:X:Y:Z<file-name>.vdisk"

#============================================================================
#
# Uncomment to connect the emulator's DKA300 DKA100 to the host's CD/DVD-ROM a host disk drive.
#
#----------------------------------------------------------------------------

#load virtual_scsi_cdrom disk pka_3 1 scsi_bus=pka scsi_id=31
#set pka_3 1 container="\\.\CdRom0PhysicalDrive0"
#set pka_3 1 container="\\.\CdRomNPhysicalDriveN"

#============================================================================
#
# Uncomment to connect the emulator's DKA400 to an .ISO file (DKA300 to the host's CD/DVD image)-ROM drive.
#
#----------------------------------------------------------------------------

#load virtual_scsi_cdrom pka_4 3 scsi_bus = pka scsi_id = 43
#set pka_3 container="\\.\CdRom0"
#set pka_4 3 container="<file-name>.iso\\.\CdRomN"

#============================================================================
#
# Uncomment to connect the emulator's MKA500 to the host's SCSI tape driveDKA400 to an .ISO file (CD/DVD image).
#
#----------------------------------------------------------------------------

#load physicalvirtual_scsi_device cdrom pka_5 4 scsi_bus=pka scsi_id=54
#set pka_5 4 container="\\.\Tape0"
#set pka_5 container="\\.\TapeN<file-name>.iso"

#============================================================================
#
# Uncomment to connect the emulator's MKA600 to a .VTAPE file (tape image)MKA500 to the host's SCSI tape drive.
#
#----------------------------------------------------------------------------

#load virtual_scsi_tape pka_6 5 scsi_bus=pka scsi_id=6=5
#set pka_5 container="\\.\Tape0"
#set pka_6 5 container="<file-name>.vtape\\.\TapeN"

#============================================================================
#
# If necessary, load an optional SCSI controller SCSI_B (PKB).
#
# ATTENTION! Old versions of VAX/VMS (older then 5.5-2H4) do not support
# the optional SCSI controller and may fail to boot if this option is loadedUncomment to connect the emulator's MKA600 to a .VTAPE file (tape image).
#
#----------------------------------------------------------------------------

#include kzdda.icfg

#

#load virtual_scsi_tape pka_6 scsi_bus=pka scsi_id=6
#set pka_6 container="<file-name>.vtape"

#=================================================================================
#
# Uncomment to connect the emulator's DKB600, DKB601 to the host's floppy disk
# drives (A:, B:, if any)=
#
# If necessary, load an optional SCSI controller SCSI_B (PKB).
#
# ATTENTION! Old versions of VAX/VMS (older then 5.5-2H4) do not support
# the optional SCSI controller and may fail to boot if this option is loaded.
#
#----------------------------------------------------------------------------#load floppy_scsi_device pkb_6 scsi_bus=pkb scsi_id=6---

#include kzdda.icfg

#============================================================================
#
# Uncomment to enable the built-in SGEC Ethernet Adapter (EZAto connect the emulator's DKB600, DKB601 to the host's floppy disk
# drives (A:, B:, if any).
#
#----------------------------------------------------------------------------

#set EZA interface=EZA0#load floppy_scsi_device pkb_6 scsi_bus=pkb scsi_id=6

#============================================================================
#
# Enable the built-in SGEC Ethernet Adapter (EZA).
#
# Connect the SGEC Ethernet Adapter (EZA) to the host's NIC.TIP: You need to uncomment the "set EZA ..." line and one of the
# "load packet_port ..." lines below to attach the EZA to host NIC (or not)
#
#----------------------------------------------------------------------------

#set EZA interface = EZA0

# choose this one to leave EZA unconnected
#load packet_port EZA0 interface = "(disabled)")"

# choose this one to connect EZA to host's NIC (by its connection name)
#load packet_port EZA0 interface = "connection:<connection-name>"

...

#load physical_serial_line /chserial TXA0 line="\\.\COMn"
#load virtual_serial_line /chserial TXA0 port=10010
#load virtual_serial_line /chserial TXA0 port=10010 application="txa0.ht"
#set TXA line[0]=TXA0

#load physical_serial_line /chserial TXA1 line="\\.\COMn"
#load virtual_serial_line /chserial TXA1 port=10011
#load virtual_serial_line /chserial TXA1 port=10011 application="txa1.ht"
#set TXA line[1]=TXA1

#load physical_serial_line /chserial TXA2 line="\\.\COMn"
#load virtual_serial_line /chserial TXA2 port=10012
#load virtual_serial_line /chserial TXA2 port=10012 application="txa2.ht"
#set TXA line[2]=TXA2

#load physical_serial_line /chserial TXA3 line="\\.\COMn"
#load virtual_serial_line /chserial TXA3 port=10013
#load virtual_serial_line /chserial TXA3 port=10013 application="txa3.ht"
#set TXA line[3]=TXA3

#load physical_serial_line /chserial TXA4 line="\\.\COMn"
#load virtual_serial_line /chserial TXA4 port=10014
#load virtual_serial_line /chserial TXA4 port=10014 application="txa4.ht"
#set TXA line[4]=TXA4

#load physical_serial_line /chserial TXA5 line="\\.\COMn"
#load virtual_serial_line /chserial TXA5 port=10015
#load virtual_serial_line /chserial TXA5 port=10015 application="txa5.ht"
#set TXA line[5]=TXA5

#load physical_serial_line /chserial TXA6 line="\\.\COMn"
#load virtual_serial_line /chserial TXA6 port=10016
#load virtual_serial_line /chserial TXA6 port=10016 application="txa6.ht"
#set TXA line[6]=TXA6

#load physical_serial_line /chserial TXA7 line="\\.\COMn"
#load virtual_serial_line /chserial TXA7 port=10017
#load virtual_serial_line /chserial TXA7 port=10017 application="txa7.ht"
#set TXA line[7]=TXA7

...

#============================================================================
#
# Configuring an optional DELQA Ethernet adapters (QBUS).=
#
# Load optional DELQA QBUS Ethernet Adapter (XQA).
#
# TIP: You need to uncomment the "load DELQA ..." line and one of the
# "load packet_port ..." lines below to attach the XQA to host NIC (or not)
#
#----------------------------------------------------------------------------

#load DELQA /DEQNA XQAXQA interface = XQA0

# choose this one to leave XQA unconnected
#load packet_port XQA0 interface = "connection:<connection-name>"
#set XQA interface=XQA0#load DELQA XQB address=...
#load DELQA XQC address=...(disabled)"

# choose this one to connect XQA to host's NIC (by its connection name)
#load packet_port XQA0 interface = "connection:<connection-name>"

#============================================================================
#
# Configure an optional DHV11 (or DHQ11, CXY08, CXA16, CXB16) serial line
# controller (QBUS). The address and vector must be set as required by the
# guest operating system.
#
#----------------------------------------------------------------------------