| Anchor | ||||
|---|---|---|---|---|
|
| Include Page | ||||
|---|---|---|---|---|
|
##
...
Copyright
...
(C)
...
1999-
...
2016 STROMASYS#
...
All
...
rights
...
reserved.##
...
The
...
software
...
contained
...
on
...
this
...
media
...
is
...
proprietary
...
to
...
and
...
embodies#
...
the
...
confidential
...
technology
...
of
...
STROMASYS.
...
Possession,
...
use,
...
duplication,#
...
or
...
dissemination
...
of
...
the
...
software
...
and
...
media
...
is
...
authorized
...
only
...
pursuant#
...
to
...
a
...
valid
...
written
...
license
...
from
...
STROMASYS.##============================================================================
...
set
...
session
...
hw_model
...
=
...
PDP1193
#============================================================================##
...
Choose a name for the instance, if needed, to differentiate it among other# instances running on the same host.##----------------------------------------------------------------------------
...
include configuration_name
...
.icfg
#============================================================================##
...
Use the following commands to disable the rotating LOG files and enable# a single LOG file. Select either append or overwrite (for each time the# instance starts) and specify desired log path and file name.##----------------------------------------------------------------------------
...
set session
...
log_method
...
=
...
append#set
...
session
...
log_method
...
=
...
overwrite#set
...
session
...
log
...
=
...
PDP1193.log
set
...
toy
...
container
...
=
...
"pdp1193.dat"
##
...
Specify
...
KW11-L
...
timer
...
frequency
...
here
...
(default
...
is
...
50).
...
Note,
...
that
...
appropriate#
...
disk
...
image
...
supports
...
appropriate
...
frequency
...
because
...
system
...
clock#
...
frequency
...
is
...
the
...
system
...
configuration
...
parameter.#
#set
...
KW11
...
frequency
...
=
...
50#set
...
KW11
...
frequency
...
=
...
60
#load physical_serial_line TT0 line = "\\.\COM<N>"
#load virtual_serial_line TT0 port = 10003
load virtual_serial_line TT0 port = 10003 application = "putty -load TT0 -P 10003"
set UART line = TT0
#============================================================================
#
# Uncomment to enable emulation of RQDX3 disk controller.
#
#----------------------------------------------------------------------------
#load RQDX3 DU#============================================================================
#
# Uncomment to connect the emulator's DU0 to the disk image.
#
#----------------------------------------------------------------------------
#set DU container[0] = "<file-name>.vdisk"#============================================================================
#
# Uncomment to connect the emulator's DU1 to host's disk drive.
#
#----------------------------------------------------------------------------
#set DU container[1] = "\\.\PhysicalDrive0"
#set DU container[1] = "\\.\PhysicalDrive<N>"
#============================================================================
#
# Uncomment to connect the emulator's DU2 to host's CD/DVD-ROM drive or ISO
# disk image.
#
#----------------------------------------------------------------------------
#set DU container[2] = "\\.\CdRom0"
#set DU container[2] = "\\.\CdRom<N>"
#set DU container[2] = "<file-name>.iso"
#============================================================================
#
# Uncomment to connect the emulator's DU3 to host's 3.5" FDD.
#
# Either "A:" or "B:" may be used in container specification.
#
#----------------------------------------------------------------------------
#set DU container[3] = "\\.\A:"#============================================================================
#
# Boot from DU0 MSCP disk.
#
#----------------------------------------------------------------------------
#set cpu_0 auto_boot = "DU0"#============================================================================
#
# Uncomment to enable emulation of TQK50 tape controller.
#
#----------------------------------------------------------------------------
#load TQK50 MU#============================================================================
#
# Uncomment to connect the emulator's MU0 to the tape image.
#
#----------------------------------------------------------------------------
#set MU container[0] = "<file-name>.vtape"#============================================================================
#
# Uncomment to connect the emulator's MU1 to host's tape drive.
#
#----------------------------------------------------------------------------
#set MU container[1] = "\\.\Tape0"
#set MU container[1] = "\\.\Tape<N>"
#============================================================================
#
# Load optional DEQNA QBUS Ethernet Adapter (QNA).
#
#----------------------------------------------------------------------------
#load DEQNA QNA interface = QNA0
#load packet_port QNA0 interface = (disabled)
#set QNA0 interface = "connection:<connection-name>"
# this is the end of the configuration file #################################
...
#
...
# Now assign console built-in serial line. Currently the emulator offers two# possible ways using serial lines. First of them is connection to COM ports# (via physical_serial_line). The second is to attach a third party terminal# emulator (virtual_serial_line).#
#load physical_serial_line TT0 line="COM1:"#load virtual_serial_line TT0 port=10003#load virtual_serial_line TT0 port=10003 application="opa0.ht"load virtual_serial_line TT0 port=10003 application="putty -load OPA0"set uart line=TT0
## Configure an optional RQDX3 storage controller (MSCP/QBUS). It handles disk# images, disk drives, CD-ROM drives, magneto-optical drives, floppy drives.#
#load RQDX3 DU#set DU container[0]="..."#set DU container[1]="..."#set DU container[2]="..."#set DU container[3]="..."
# Boot from DU0 MSCP disk#set cpu_0 auto_boot="DU0"
# this is the end of the configuration file ##################################
| Include Page | ||||
|---|---|---|---|---|
|