Page Comparison

$ PRODUCT INSTALL */SOURCE=DKA400:[DIGIBOARD]/HELP
 
   1 - DIGI AXPVMS DGDRIVER D1.3-0 Layered Product
   2 - DIGI AXPVMS DGDRIVER_7 D1.3-0 Layered Product
   3 - DIGI AXPVMS DGDRIVER_8 D1.5-0 Layered Product
   4 - All products listed above
   ? - Help
   E - Exit
 
Choose one or more items from the menu: 3
%PCSI-I-CANNOTVAL, cannot validate DKA400:[DIGIBOARD]DIGI-AXPVMS-DGDRIVER_8-D0105-0-1.PCSI;1
-PCSI-I-NOTSIGNED, product kit is not signed and therefore has no manifest file
 
%PCSI-W-SFTREF, product DEC AXPVMS VMS V8.3 references product DEC AXPVMS DWMOTIF_SUPPORT
 
    The referenced product is not installed and a kit for it was not found
    in the source directory.
 
    It is not yet known if this reference is a "hard" or a "soft" dependency.
    If the product you are installing identifies the referenced product as a
    prerequisite, the PCSI utility will terminate the installation after the
    configuration phase, but before the execution phase begins. However, if
    the software dependency is expressed as part of a configuration option
    of the product, the PCSI utility will mark the option as unselectable
    during the configuration phase so that the product can be installed.
 
Do you want to continue? [YES] YES
 
The following product has been selected:
    DIGI AXPVMS DGDRIVER_8 D1.5-0 Layered Product
 
Do you want to continue? [YES] YES
 
Configuration phase starting ...
 
You will be asked to choose options, if any, for each selected product and for
any products that may be installed to satisfy software dependency requirements.
 
DIGI AXPVMS DGDRIVER_8 D1.5-0: Digi AccelePort Device Driver for VMS 8.x
 
    The Digi AccelePort Device Driver package allows a VMS system administrator
    to install, configure, and use the following intelligent, multi-connect
    serial adapters:
 
    o Digi AccelePort Xr adapters for ISA and PCI
 
    o Digi AccelePort Xr 920 adapters for ISA and PCI
 
    o Digi AccelePort EPC adapters for ISA, EISA and PCI
 
    o Digi AccelePort Xem adapters for ISA, EISA and PCI
 
    o Digi AccelePort C/X adapters for ISA, EISA and PCI
 
    © Digi International 1995. All rights reserved.
 
    Copyright (c) 1988-96 Digi International Inc., All Rights Reserved
 
    This software contains proprietary and confidential information of
    Digi International Inc. By accepting transfer of this copy, Recipient
    agrees to retain this software in confidence, to prevent disclosure to
    others, and to make no use of this software other than that for which it
    was delivered. This is an unpublished copyright work Digi International
    Inc. Except as permitted by federal law, 17 USC 117, copying is
    strictly prohibited.
 
    Digi International Inc. CONFIDENTIAL - (Digi International Inc.
    Confidential when combined with the aggregated modules for this
    product) OBJECT CODE ONLY SOURCE MATERIALS
 
    (C) COPYRIGHT Digi International Inc. 1996
 
    All Rights Reserved
 
    US Government Users Restricted Rights - Use, duplication or
    disclosure restricted by GSA ADP Schedule Contract with Digi International
    Inc.
 
    Digi International
 
    This software product is sold by:
 
        Digi International
 
Do you want the defaults for all options? [YES] YES
 
    The /HELP option is required; if you didn't use it, do not continue.
 
    (If you can read this text, the /HELP option was used)
 
 
    Do you want to continue? [YES] YES
 
Do you want to review the options? [NO] NO
 
Execution phase starting ...
 
The following product will be installed to destination:
    DIGI AXPVMS DGDRIVER_8 D1.5-0 DISK$TARDISSYSTEM:[VMS$COMMON.]
 
Portion done: 0%...10%...20%...30%...40%...50%...60%...70%...80%...90%...100%
 
The following product has been installed:
    DIGI AXPVMS DGDRIVER_8 D1.5-0 Layered Product
 
DIGI AXPVMS DGDRIVER_8 D1.5-0: Digi AccelePort Device Driver for VMS 8.x
 
    Post Installation Procedure
 
    The installation procedure has created the logical "DIGI$DRIVER"
    which defines the location of the installed software kit. To ensure
    that this logical is defined after each reboot, add the contents of
    the following file to the SYS$STARTUP:SYLOGICALS.COM file:
 
          DIGI$DRIVER:MAKE_DIGI_LOGICAL.COM
 
    Once the installation procedure is complete, you must configure the
    driver by executing the following command:
 
          @DIGI$DRIVER:DG_SETUP.COM
 
    This configuration command should be executed once now, and once each
    time that the hardware configuration changes. This command procedure
    automates driver configuration, and will generate a command procedure
    to be added to the system startup as described below.
 
    You should take the time to examine the release notes which are
    included in this distribution. To find these notes, execute the
    following commands:
 
          $ SET DEFAULT DIGI$DRIVER:
          $ SET DEFAULT [.RELNOTES]
          $ DIR
 
    Users of this product require the following process resource limits:
        BYTLM minimum 45000
 
    This product requires the following SYSGEN parameters:
        MAXBUF minimum 45000
 
    Insert the following lines in SYS$MANAGER:SYSTARTUP_VMS.COM:
 
        $! DON'T FORGET TO REMOVE THE ! FROM THE LINE BELOW
        $! @DIGI$DRIVER:DIGI_INSTALL_EPCA.COM