General description

CHARON-AXP supports emulation of DEC-KGPSA-CA PCI Fibre Channel adapter.

Every instance of KGPSA-CA works in one of the two following modes:

Fabric virtualization mode (creating virtual fabric in combination with virtual FC-3 Storage Controller). This is default mode.
Pass Through mode (using a specific CHARON PCI Pass Through driver)
Fabric presentation mode (using Linux FC HBA directly)

Loading KGPSA storage adapter

Syntax for loading KGPSA-CA storage adapter:

load KGPSA <name>

Example:

load KGPSA FGA

In AlphaStation 400 configuration use the following syntax for KGPSA-CA storage adapter loading:

load KGPSA FGA irq_bus=isa

The adapter instance name ("FGA" in the example above) is used then for parametrization, for example:

set FGA container[100]="/my_disks/vms_distributive.vdisk"

Numbers in the square brackets represent KGPSA-CA units. They can be in the range 0..32766, but no more than 255 units can be configured on a single controller.

By default KGPSA-CA adapter uses first available PCI slot. If instead some particular slot is needed, refer to this section for details of specific placement of PCI peripherals on CHARON-AXP PCI bus.

Configuration parameters

The KGPSA-CA PCI FC adapter emulation has the following configuration parameters:

host_bus_location

Parameter host_bus_location

Type Text String

Value

Pass Through mode mode only!

Establish connection between virtual DEC-KGPSA-CA PCI FC adapter and physical EMULEX LightPulse PCI/PCI-X/PCIe FC adapter (Pass Through mode)

Syntax:

load KGPSA <controller name> host_bus_location="/dev/kgpsa<X>"

Example:

load KGPSA FGA host_bus_location="/dev/kgpsa0"

wwid

Parameter

wwid[N]

N is 0..32766 (no more than 255 units)

Type Text String

Value

Sets WWID for emulated KGPSA adapter unit.

Syntax:

set <controller name> wwid[unit-number]="XXXX-XXXX-XXXX-XXXX-XXXX-XXXX-XXXX-XXXX"

Example:

set FGA wwid[2]="6008-05F3-0005-2950-BF8E-0B86-A0C7-0001"

container

Parameter

container[N]

N is 0..32766 (no more than 255 units)

Type

Text String

Value

Possible values of the parameter are strings in one of the following forms:

Physical disk
- "/dev/sd<L>", where "L" is letter, for example "/dev/sdb"
- "/dev/disk/by-id/..." - addressing by the disk ID, for example "/dev/disk/by-id/ata-ST1000DM003-9YN162_S1D01QJ4"
- "/dev/disk/by-label/..." - addressing by the disk label, for example "/dev/disk/by-label/MyStorage"
- "/dev/disk/by-uuid/..." - addressing by the disk UUID, for example "/dev/disk/by-uuid/0e808a2f-cdd3-4944-a245-f729ffd73882"
  Please note that existing data on such a disk may be destroyed, depending on how it is used in the emulator.
  
  "/dev/sd<L>" addressing is not persistent, so it is strongly recommended to use "/dev/disk/by-id/wwn-*" syntax instead to refer the disk by its WWID - especially in the enviroments utilizing FC and SAN storages.
  These disks must not be formatted by the host OS.
  Example:
  set FGA container[0]="/dev/disk/by-id/ata-ST1000DM003-9YN162_S1D01QJ4"
  It is also possible to use not a whole disk, but previously created partitions on it. In this case the syntax is the following: "/dev/sd<L><N>" where N is the number of partition to be used.
  Example:
  set FGA container[0]="/dev/sdc3"
  .Loop (virtual block) devices
Loop (virtual block) devices
- "/dev/loop<N>"
  Example:
  set FGA container[100]="/dev/loop0"
Multipath disk
- "/dev/dm-<N>"
- "/dev/mapper/mpath<N>"
- "/dev/mapper/disk<N>"
  Be careful not to destroy all the information from the disk dedicated to CHARON-AXP by mistake.
  These disks must not be formatted by the host OS.
  Example:
  set FGA container[200]="/dev/dm-0"
  .
File representing a physical disk of the HP Alpha system (disk image)
- [<drive>":\"<path-name>”\”]<file-name>[“.vdisk”]
  These files can be created from scratch with "mkdskcmd" utility. Data and OS disk backups are transferred from the original system via tapes or network and restored into these container files.
  Mapping may also include the full path (recommended), for example: "/my_disks/my_boot_disk.vdisk"
  Example:
  set FGA container[401]="my_dka401.vdisk"
  .

This parameter is initially not set, thus creating NO storage elements on the controller.

media_type

Parameter

media_type[N]

N is 0..32766 (no more than 255 units)

Type

Text String

Value

Instructs CHARON-AXP to use the supplied value as the PRODUCT field in the FC INQUIRY data returned to a software running on virtual HP Alpha system in response to FC INQUIRY command.

If not specified, CHARON-AXP attempts to guess the FC INQUIRY data based on virtual FC device type and underlying container (which is specified in the corresponding container configuration parameter).

Initially is not specified.

Example:

set FGA media_type[0]="HSZ70"

removable

Parameter

removable[N]

N is 0..32766 (no more than 255 units)

Type Boolean

Value

When set to "true", the removable configuration parameter instructs CHARON-AXP to report the corresponding virtual FC device as removable.

By default the removable configuration parameter is set to "false".

Example:

set FGA removable[400]=true

geometry

Parameter

geometry[N]

N is 0..32766 (no more than 255 units)

Type

Text String

Value

This formatted string value specifies the explicit geometry of the disk storage element.

The string format is <X>”/”<Y>[“/”<Z>] or <X>”,”<Y>[“,”<Z>][“,”<B>] where:

Parameter	Description
X	The number of sectors per track
Y	The number of tracks per cylinder
Z	The number of cylinders on the unit. If omitted, Z is calculated based on X, Y and the total number of sectors on the unit that reflects the size of the disk storage element. This is an optional parameter.
B	The total size of the disk (in blocks) reported to the guest OS. If omitted it is calculated automatically. This is an optional parameter.

If this parameter is not set, CHARON-AXP will configure the geometry based on the most probable disk type.

Initially not set.

Example:

set FGA geometry[201] = "255/255"

It is possiblle to specify each parameter independently of another one. The following syntax is used for that:

set FGA geometry[300]="*,*,*,16777210"

use_io_file_buffering

Parameter

use_io_file_buffering[N]

N is 0..32766 (no more than 255 units)

Type

Boolean

Value

When set to "true", instructs CHARON-AXP to enable host operating system I/O cache on read/write operations.

Note that this caching has a significant effect only in case of mapping to disk containers, not physical drives.

When enabled, host operating system I/O cache may significantly improve I/O performance of the virtual system. At the same time maintaining I/O cache requires additional host resources (CPU and memory) which may negatively affect overall performance of the virtual system.

Initially is set to "false".

Example:

set FGA use_io_file_buffering[300]=true

io_queue_depth

Parameter

io_queue_depth[N]

N is 0..32766 (no more than 255 units)

Type Numeric

Value

Specifies KGPSA I/O requests (read or write) for a given unit in a range 2..128

Setting this parameter enables KZPBA instance to run up-to the specified numbers of I/O requests (read or write) for unit N in parallel, thus improving the performance.

The default value set by controller is optimal for most of the cases. It may be needed to enlarge this number if guest OS I/O queue for a certain unit contains too much pending entries. In this case the value should be equal to an average size of the queue, collected statistically.

Please do not set this parameter without clear understanding of the purpose.

By default parallel execution of I/O requests is disabled.

Example:

set FGA io_queue_depth[603]=4

min_n_of_threads

Parameter

min_n_of_threads

Type Numeric

Value

Instructs KGPSA I/O to reserve a given number of working threads in a range 1..64, thus improving the performance.

All units of KGPSA instance share the I/O threads.

The default value is equal to number of units plus 2.

For optimization it is possible to set this parameter to sum of the "io_queue_depth" parameters for each unit plus 2. This assumption seems optimal for most of the cases.

Please do not set this parameter without clear understanding the purpose.

Example:

set FGA min_n_of_threads=16

When a disk image connected to an emulated KGPSA-CA controller is dismounted by OpenVMS, it is disconnected from CHARON-AXP and can be manipulated. It can be replaced with a different disk image if it keeps the same name. This capability may be useful when designing back-up and restore procedures. When copying CHARON-AXP disk images while CHARON-AXP is running, please take care to minimize the risk of overloading a heavily loaded CHARON-AXP host system. For example, using a sequential series of simple ftp binary copies is less resource intensive and thus less disruptive than multiple, simultaneous copies.

Empty disk images are created with the "mkdskcmd" utility.

CHARON-AXP is able to boot from disk images of any OpenVMS/Alpha and Tru64 version.

Mapping to host resources

Fabric virtualization mode

In this mode KGPSA-CA PCI FC adapter can be directly mapped to physical disks (both local and iSCSI) and disk images as shown in the following example:

set FGA container[0]="/my_disks/my_dka401.vdisk"set FGA container[100]="/dev/sdb"
set FGA container[200]="/dev/sdc2"
set FGA container[300]="/dev/dm-0"

See the "Configuration parameters" section for details.

Pass Through mode

The CHARON PCI Pass Through mode allows connection between virtual DEC-KGPSA-CA PCI FC adapter and physical EMULEX LightPulse PCI/PCI-X/PCIe FC adapter plugged into host’s PCI/PCI-X/PCIe slot.

Syntax:

load <controller name> host_bus_location="/dev/kgpsa<N>"

Example:

load KGPSA FGA host_bus_location="/dev/kgpsa0"

The following is a list of EMULEX LightPulse PCI/PCI-X/PCIe FC adapters supported by CHARON-AXP PCI Pass Through driver and suitable for emulation of KGPSA-CA PCI FC adapter in CHARON PCI Pass Through mode:

Supported	Not Supported	Not tested
LP8000 LP9000 LP9002 LP9802 LP10000 LP10000DC LP10000-S LPX1000 LP11002 LPe11002 (FC2242SR, A8003A) LPe1105 LPe12002 (AJ762B)	LPe1150 (FC2142SR, A8002A)	LPe11000

Pass Through mode establishing sequence

To establish "pass through" mode do the following:

Install the EMULEX LightPulse PCI/PCI-X/PCIe FC adapter (see above for a list of supported models) to some spare PCI/PCI-X/PCIe slot of the host system
Build PPT driver for EMULEX LightPulse PCI/PCI-X/PCIe FC
Install PPT driver for EMULEX LightPulse PCI/PCI-X/PCIe FC
Add PPT driver for EMULEX LightPulse PCI/PCI-X/PCIe FC to Linux startup
Map KGPSA-CA adapter(-s) to EMULEX LightPulse PCI/PCI-X/PCIe FC adapter instance(-s) in CHARON-AXP configuration file

If kernel of the host system has been upgraded or reinstalled all the steps of the PPT KGPSA driver installation must be repeated

Building PPT driver for EMULEX LightPulse PCI/PCI-X/PCIe FC

To build PPT driver for EMULEX LightPulse PCI/PCI-X/PCIe FC do the following:

Step Description

1

Make sure that the required building tools and include files are installed. If they are absent install them:

# yum groupinstall “Development Tools”
# yum install kernel-headers kernel-develop

The kernel version must match the version of the installed kernel-headers (i.e. this packages must have same versions. It can be verified via "rpm -q -a | grep kernel-" )

Check that the "kernel" and the "kernel-headers" have the same version, and ensure that system is booted from this kernel version (not from some older one and etc) with "uname -a" command.

2

Open xterm and change the default directory to "/opt/charon/drivers/kgpsa":

# cd /opt/charon/drivers/kgpsa

3

Issue "make clean; make" commands to build kernel object:

# make clean; make

It is prohibited to use a module built on a certain version of kernel on another one.

4 Check that there are no compilation errors and the file "ppt_kgpsa.ko" has been built

Installation of PPT driver for EMULEX LightPulse PCI/PCI-X/PCIe FC

To install PPT driver for EMULEX LightPulse PCI/PCI-X/PCIe FC do the following:

Step Description

1

Unload standard "lpfc" driver; to do that issue the following command:

# rmmod lpfc

2

Load "ppt_kgpsa.ko" driver; to do that issue the following command:

# insmod ppt_kgpsa.ko

3

Issue "dmesg" command and check that no error appeared during the driver loading, also check that the driver has found all KGPSA devices:

# dmesg

Adding PPT driver for EMULEX LightPulse PCI/PCI-X/PCIe FC to Linux startup

To add PPT driver for EMULEX LightPulse PCI/PCI-X/PCIe FC to Linux startup do the following:

Step Description

1 Disable auto-loading of Linux standard "lpfc" driver on boot. To do that add "blacklist lpfc" to the black list file "/etc/modprobe.d/blacklist.conf"

2

Copy the KGPSA-CA kernel module to the location of Linux kernel modules, for example:

# cp /opt/charon/drivers/kgpsa/ppt_kgpsa.ko /lib/modules/3.10.9-200.fc20.x86_64/kernel/drivers/scsi/

The particular path may be different, depending on the kernel version and Linux distribution.

3

Enable auto load of the module:

# echo ppt_kgpsa > /etc/modules-load.d/ppt_kgpsa.conf

4

Regenerate new "initramfs" image with "mkinitrd":

# mkinitrd -f /boot/initramfs-3.10.9-200.fc20.x86_64.img 3.10.9-200.fc20.x86_64

The particular path may be different, depending on the kernel version and Linux distribution.

Configuration of KGPSA-CA in pass through mode

FCMGR utility description

To configure KGPSA-CA adapter in pass through mode a special SRM console utility "FCMGR" is used (it has the same functionality as the "WWIDMGR" utility of the native HP Alpha hardware).

It provides the following functionality:

Command	Description
`fc rescan {/verbose}`	Scans connected SAN using FC adapters, discovers FC ports, storage controllers, logical units and then builds volatile FC database. The "/verbose" qualifier enables FC communication trace on console (for diagnostic and troubleshooting).
`fc show {adapter \| port \| device}`	Displays corresponding part of volatile FC database.
`fc set {boot \| dump} udid <X>`	Fills the environment variables wwid0..wwid3 and n1..n4 to identify path(s) to logical unit with the specified UDID. These variables are later used by "INIT" to create device database entries and by OpenVMS/Tru64 to get access to boot and dump disks. This command does NOT make any change to other environment variables.
`fc set {boot \| dump} wwid <X>`	Fills the environment variables wwid0..wwid3 and n1..n4 to identify path(s) to logical unit with the specified WWID. These variables are later used by "INIT" to create device database entries and by OpenVMS/Tru64 to get access to boot and dump disks. This command does NOT make any change to other environment variables. This parameter is useful if UDID is absent. Only right part of the displayed WWID is used for specification, for example: `P00>>>fc res` `polling for units on kgpsa0, slot 2, bus 0, hose 0 ...` `pga0.0.0.2.0 PGA0 F/W Rev 2.72A2` `WWN 1000-0000-0263-0040` `fabric WWN 2003-0060-0263-0040` `directory WWN 20fc-0060-0263-0040` `port 020100 CED 8GSH 0 F88V` `WWN 5000-1fe0-0000-0bf1` `lun 0000000000000000 DEC HSG80CCL V88F` `UDID:-1 WWID:01000010:6000-1fe0-0000-0bf0-3030-3030-373f-3f3f` `lun 0000000000000100 COMPAQ RZ1ED 0000` `UDID:-1 WWID:01000010:6000-1fe0-0000-0bf0-3030-3030-3030-3030` `P00>>>fc set boot wwid 6000-1fe0-0000-0bf0-3030-3030-3030-3030`
`fc clear`	Clears environment variables wwid0..wwid3 and n1..n4, which automatically disable (but do NOT delete) device database entries representing FC attached devices. This command does NOT affect volatile FC database.

Example of usage:

P00>>>fc show devices
     UDID:110 WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-0081 (ev:none)
                                               via adapter     via fc_port         con
[0]                   pga0.0.0.5.1    5000-1fe1-000b-6bf1 yes (ev:none)
[1]                   pga0.0.0.5.1    5000-1fe1-000b-6bf4 yes (ev:none)
   UDID:108 WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-0039 (ev:none)
                                               via adapter     via fc_port         con
[12]                  pga0.0.0.5.1    5000-1fe1-000b-6bf1 yes (ev:none)
[13]                  pga0.0.0.5.1    5000-1fe1-000b-6bf4 yes (ev:none)

Configuration steps using FCMGR utility

Once the configuration steps described above are done, start the CHARON VM and wait for the P00>>> prompt.

Please refer to the following example with two FC adapters PGA and PGB defined:

initializing ...

polling for units on kzpba0, slot 4, bus 0, hose 0 ...
pka0.0.0.4.0 PKA0 Q-Logic/ISP PCI SCSI HBA

polling for units on kgpsa0, slot 5, bus 0, hose 0 ...
   pga0.0.0.5.0         PGA0            WWN 1000-0000-C92E-97C9
      fabric                            WWN 2003-0060-6920-4682
         directory                      WWN 20fc-0060-6920-4682
         port 021400                    WWN 5000-1fe1-000b-6bf1
            lun 0000000000000100        DEC     HSG80           V88F
         UDID:100       WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-0038
            lun 0000000000000200        DEC     HSG80 V88F
         UDID:200 WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-0074
            lun 0000000000000300        DEC HSG80 V88F
         UDID:300       WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-007b
            lun 0000000000000400    DEC HSG80 V88F
         UDID:400       WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-0080
            lun 0000000000006c00        DEC     HSG80 V88F
         UDID:108       WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-0039
            lun 0000000000006d00    DEC HSG80 V88F
         UDID:208       WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-003a
            lun 0000000000000000

         port 021500                    WWN 5000-1fe1-000b-6bf4
            lun 0000000000000100        DEC     HSG80 V88F
         UDID:100       WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-0038
            lun 0000000000000200        DEC     HSG80 V88F
         UDID:200       WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-0074
            lun 0000000000000300        DEC HSG80 V88F
         UDID:300 WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-007b
            lun 0000000000000400        DEC HSG80 V88F
         UDID:400 WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-0080
            lun 0000000000006c00        DEC HSG80 V88F
         UDID:108 WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-0039
            lun 0000000000006d00        DEC HSG80 V88F
         UDID:208 WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-003a
            lun 0000000000000000

polling for units on kgpsa1, slot 6, bus 0, hose 0 ...
   pgb0.0.0.6.0         PGB0    WWN 1000-0000-C92D-8D00
      fabric                            WWN 2003-0060-6920-45ff
         directory                      WWN 20fc-0060-6920-45ff
         port 011400                    WWN 5000-1fe1-000b-6bf2
            lun 0000000000000100        DEC     HSG80           V88F
         UDID:100 WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-0038
            lun 0000000000000200        DEC     HSG80           V88F
         UDID:200 WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-0074
            lun 0000000000000300        DEC     HSG80           V88F
         UDID:300 WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-007b
            lun 0000000000000400        DEC     HSG80           V88F
         UDID:400 WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-0080
            lun 0000000000006c00        DEC     HSG80           V88F
         UDID:108 WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-0039
            lun 0000000000006d00        DEC     HSG80           V88F
         UDID:208 WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-003a
            lun 0000000000000000
         port 011500                    WWN 5000-1fe1-000b-6bf3
            lun 0000000000000100        DEC     HSG80           V88F
         UDID:100 WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-0038
            lun 0000000000000200        DEC     HSG80           V88F
         UDID:200 WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-0074
            lun 0000000000000300        DEC     HSG80           V88F
         UDID:300 WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-007b
            lun 0000000000000400        DEC     HSG80           V88F
         UDID:400 WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-0080
            lun 0000000000006c00        DEC     HSG80           V88F
         UDID:108 WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-0039
            lun 0000000000006d00        DEC     HSG80           V88F
         UDID:208 WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-003a
            lun 0000000000000000
         port 011100                    failed port login

... enter console

P00>>>

The next step is to configure paths for the FC storage:

P00>>>fc show devices

     UDID:100 WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-0038 (ev:none)
                        via adapter     via fc_port         con
[0]                     pga0.0.0.5.0    5000-1fe1-000b-6bf1 no (ev:none)
[1]                     pga0.0.0.5.0    5000-1fe1-000b-6bf4 yes (ev:none)
[2]                     pgb0.0.0.6.0    5000-1fe1-000b-6bf2 no (ev:none)
[3]                     pgb0.0.0.6.0    5000-1fe1-000b-6bf3 yes (ev:none)
     UDID:200 WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-0074 (ev:none)
                        via adapter     via fc_port         con
[4]                     pga0.0.0.5.0    5000-1fe1-000b-6bf1 no (ev:none)
[5]                     pga0.0.0.5.0    5000-1fe1-000b-6bf4 yes (ev:none)
[6]                     pgb0.0.0.6.0    5000-1fe1-000b-6bf2 no (ev:none)
[7]                     pgb0.0.0.6.0    5000-1fe1-000b-6bf3 yes (ev:none)
     UDID:300 WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-007b (ev:none)
                        via adapter     via fc_port         con
[8]                     pga0.0.0.5.0    5000-1fe1-000b-6bf1 no (ev:none)
[9]                     pga0.0.0.5.0    5000-1fe1-000b-6bf4 yes (ev:none)
[10]                    pgb0.0.0.6.0    5000-1fe1-000b-6bf2 no (ev:none)
[11]                    pgb0.0.0.6.0    5000-1fe1-000b-6bf3 yes (ev:none)
     UDID:400 WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-0080 (ev:none)
                        via adapter     via fc_port         con
[12]                    pga0.0.0.5.0    5000-1fe1-000b-6bf1 no (ev:none)
[13]                    pga0.0.0.5.0    5000-1fe1-000b-6bf4 yes (ev:none)
[14]                    pgb0.0.0.6.0    5000-1fe1-000b-6bf2 no (ev:none)
[15]                    pgb0.0.0.6.0    5000-1fe1-000b-6bf3 yes (ev:none)
     UDID:108 WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-0039 (ev:none)
                        via adapter     via fc_port         con
[16]                    pga0.0.0.5.0    5000-1fe1-000b-6bf1 yes (ev:none)
[17]                    pga0.0.0.5.0    5000-1fe1-000b-6bf4 no (ev:none)
[18]                    pgb0.0.0.6.0    5000-1fe1-000b-6bf2 yes (ev:none)
[19]                    pgb0.0.0.6.0    5000-1fe1-000b-6bf3 no (ev:none)
   UDID:208 WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-003a (ev:none)
                        via adapter     via fc_port         con
[20]                    pga0.0.0.5.0    5000-1fe1-000b-6bf1 yes (ev:none)
[21]                    pga0.0.0.5.0    5000-1fe1-000b-6bf4 no (ev:none)
[22]                    pgb0.0.0.6.0    5000-1fe1-000b-6bf2 yes (ev:none)
[23]                    pgb0.0.0.6.0    5000-1fe1-000b-6bf3 no (ev:none)

P00>>>fc set boot udid 400

P00>>>INIT

initializing ...

polling for units on kzpba0, slot 4, bus 0, hose 0 ...
pka0.0.0.4.0 PKA0 Q-Logic/ISP PCI SCSI HBA

polling for units on kgpsa0, slot 5, bus 0, hose 0 ...
   pga0.0.0.5.0         PGA0            WWN 1000-0000-C92E-97C9
      fabric                            WWN 2003-0060-6920-4682
         directory                      WWN 20fc-0060-6920-4682
         port 021400                    WWN 5000-1fe1-000b-6bf1
            lun 0000000000000100        DEC     HSG80           V88F
         UDID:100       WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-0038
            lun 0000000000000200        DEC     HSG80 V88F
         UDID:200 WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-0074
            lun 0000000000000300        DEC HSG80 V88F
         UDID:300       WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-007b
            lun 0000000000000400    DEC HSG80 V88F
         UDID:400       WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-0080
            lun 0000000000006c00        DEC     HSG80 V88F
         UDID:108       WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-0039
            lun 0000000000006d00    DEC HSG80 V88F
         UDID:208       WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-003a
            lun 0000000000000000
         port 021500                    WWN 5000-1fe1-000b-6bf4
            lun 0000000000000100        DEC     HSG80 V88F
         UDID:100       WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-0038
            lun 0000000000000200        DEC     HSG80 V88F
         UDID:200       WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-0074
            lun 0000000000000300        DEC HSG80 V88F
         UDID:300 WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-007b
            lun 0000000000000400        DEC HSG80 V88F
         UDID:400 WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-0080
            lun 0000000000006c00        DEC HSG80 V88F
         UDID:108 WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-0039
            lun 0000000000006d00        DEC HSG80 V88F
         UDID:208 WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-003a
            lun 0000000000000000

polling for units on kgpsa1, slot 6, bus 0, hose 0 ...
   pgb0.0.0.6.0         PGB0    WWN 1000-0000-C92D-8D00
      fabric                            WWN 2003-0060-6920-45ff
         directory                      WWN 20fc-0060-6920-45ff
         port 011400                    WWN 5000-1fe1-000b-6bf2
            lun 0000000000000100        DEC     HSG80           V88F
         UDID:100 WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-0038
            lun 0000000000000200        DEC     HSG80           V88F
         UDID:200 WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-0074
            lun 0000000000000300        DEC     HSG80           V88F
         UDID:300 WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-007b
            lun 0000000000000400        DEC     HSG80           V88F
         UDID:400 WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-0080
            lun 0000000000006c00        DEC     HSG80           V88F
         UDID:108 WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-0039
            lun 0000000000006d00        DEC     HSG80           V88F
         UDID:208 WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-003a
            lun 0000000000000000
         port 011500                    WWN 5000-1fe1-000b-6bf3
            lun 0000000000000100        DEC     HSG80           V88F
         UDID:100 WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-0038
            lun 0000000000000200        DEC     HSG80           V88F
         UDID:200 WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-0074
            lun 0000000000000300        DEC     HSG80           V88F
         UDID:300 WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-007b
            lun 0000000000000400        DEC     HSG80           V88F
         UDID:400 WWID:01000010:6000-1fe1-000b-6bf0-0009-9081-1283-0080
            lun 0000000000006c00        DEC     HSG80           V88F
         UDID:108 WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-0039
            lun 0000000000006d00        DEC     HSG80           V88F
         UDID:208 WWID:01000010:6000-1fe1-000b-6bf0-0009-0440-4014-003a
            lun 0000000000000000
         port 011100                    failed port login

... enter console

P00>>>SHOW DEV

sys0.0.0.0.0            SYS0          System ROOT Device
ewa0.0.0.3.0            EWA0          00-51-71-F5-8E-D8
pka0.0.0.4.0            PKA0          Q-Logic/ISP PCI SCSI HBA
pga0.0.0.5.0            PGA0          WWN 1000-0000-C92E-97C9
pgb0.0.0.6.0    PGB0          WWN 1000-0000-C92D-8D00
pqa0.0.0.15.0           PQA0          ALi 1553C Integrated IDE Controller
pqb0.0.1.15.0 PQB0          ALi 1553C Integrated IDE Controller
dqa0.0.0.15.0           DQA0          Virtual ATAPI - TEAC DW-224E-V
dka0.0.0.4.0            DKA0          Virtual SCSI Disk (C)SRI
dga400.1001.0.5.0       $1$DGA400     DEC     HSG80           V88F
dga400.1002.0.5.0       $1$DGA400     DEC     HSG80           V88F
dgb400.1003.0.6.0       $1$DGA400     DEC     HSG80           V88F
dgb400.1004.0.6.0       $1$DGA400     DEC     HSG80           V88F

P00>>>BOOT $1$DGA400

dga400.1001.0.5.0: failed to open device
(boot dga400.1002.0.5.0)
jumping to bootstrap code

OpenVMS (TM) Alpha Operating System, Version V7.3-2
© Copyright 1976-2003 Hewlett-Packard Development Company, L.P.
%SMP-I-CPUTRN, CPU #02 has joined the active set.
%SMP-I-CPUTRN, CPU #03 has joined the active set.
%SMP-I-CPUTRN, CPU #01 has joined the active set.
Please enter date and time (DD-MMM-YYYY HH:MM)

Fabric presentation mode

The CHARON-AXP FC Fabric presentation mode allows to use Linux FC HBA directly. When using this mode, there is no need to load KGPSA adapter(s) as it was described before. The following syntax has to be used instead:

Example:

load kgpsa_generic_storage PGA interface="host3"

Below please find step-by-step explanation on how to configure "kgpsa_generic_storage" instance.

This mode is available only for CHARON-AXP on RHEL and CentOS 7.x (and later versions) platforms

FC HBA interfaces finding

First we need to find Linux FC HBA for mapping.

List available adapters

# lspci | grep Fibre
03:00.0 Fibre Channel: Emulex Corporation Lancer-X: LightPulse Fibre Channel
Host Adapter (rev 30)
03:00.1 Fibre Channel: Emulex Corporation Lancer-X: LightPulse Fibre Channel
Host Adapter (rev 30)
0a:04.0 Fibre Channel: Emulex Corporation LP8000 Fibre Channel Host Adapter (rev 02)

So, 2 HBAs, 3 ports are available.

Load HBA's kernel modules (drivers)

# lspci -vvnn -s 03:00.0 | grep modules
	Kernel modules: lpfc

# modprobe -v lpfc

Discover the Linux SCSI hosts the FC HBAs are mapped to

# ll /sys/class/fc_host/
..
lrwxrwxrwx 1 root root 0 &#1086;&#1082;&#1090; 22 14:29 host3 ->
../../devices/pci0000:00/0000:00:01.0/0000:03:00.0/host3/fc_host/host3
lrwxrwxrwx 1 root root 0 &#1086;&#1082;&#1090; 22 14:29 host4 ->
../../devices/pci0000:00/0000:00:01.0/0000:03:00.1/host4/fc_host/host4
lrwxrwxrwx 1 root root 0 &#1086;&#1082;&#1090; 22 14:29 host6 ->
../../devices/pci0000:00/0000:00:1e.0/0000:0a:04.0/host6/fc_host/host6

So, the available ports are mapped to hosts 3, 4 and 6.

Discover the connected FC HBAs (ports)

# lsscsi
..
[2:0:0:0]    disk    ATA      Hitachi HDS72101 A610  /dev/sda 
[3:0:0:0]    storage HP       MSA CONTROLLER   7.20  -        
[3:0:0:2]    disk    HP       MSA VOLUME       7.20  /dev/sdb 
...
[5:0:0:2]    disk    Generic- USB3.0 CRW-MS/HG 1.00  /dev/sdi 
[6:0:0:0]    storage HP       MSA CONTROLLER   7.20  -

So the connected hosts are 3 and 6 ("MSA CONTROLLER").

Discover the HBAs port/node names

# cat /sys/class/fc_host/host3/port_name 
0x10000090faa00a31
# cat /sys/class/fc_host/host4/port_name 
0x10000090faa00a32
# cat /sys/class/fc_host/host6/port_name 
0x10000000c923ea51

So the names are:

Host	Mapping	Port name
3	Lancer-X, port 0 ("3:0:0:0")	0x10000090faa00a31
4	Lancer-X, port 1 ("3:0:0:1")	0x10000090faa00a32
6	LP8000 single port	0x10000000c923ea51

Charon Configuration

2 ways of specification in Charon configuration file are available:

By port name

Specify Linux port name "0x10000090faa00a31" in Charon configuration file:

load kgpsa_generic_storage PGA interface="0x10000090faa00a31"

The configuration given with port name is independent on hardware change, modules load order, etc

By host id name

load kgpsa_generic_storage PGA interface="fc_host3"

or

load kgpsa_generic_storage PGA interface="host3"

The configuration given with host id name might change on hardware change, modules load order, etc

Configuration parameters

Never use the following parameters (except the "interface") without well defined reason. Most of the parameters are implemented for solving possible problems and tracing at customer sites, so they might harm if not used appropriately.

interface

Name of FC, SCSI host or adapter's port/node name, defining a connection to Linux FC HBA, for example:

Mapping	Description
fc_host6	Emulation over Linux SG (FC) host 6
host6	Emulation over Linux SG (FC) host 6
2000-0000-C923-EA51	Emulation over Linux SG (FC) host given with port/node name
0x20000000C923EA51	Emulation over Linux SG (FC) host given with port/node name
wwn-0x20000000C923EA51	Emulation over Linux SG (FC) host given with port/node name

Example:

load kgpsa_generic_storage PGA interface="host3"

trace_level

Value	Description
0	none (default)
1	All failures and suspects
2	SCSI, ELS/CT request flow
3	MB/IOCB request flow

Example:

load kgpsa_generic_storage PGA trace_level=1

io_model

I/O model is used for request processing.

Value	Description
sync	synchronous
async	asynchronous (default)

Example:

load kgpsa_generic_storage PGA io_model="sync"

port_name

The port name in format: %04x-%04x-%04x-%04x.

Example:

load kgpsa_generic_storage PGA port_name=2000-0000-C923-EA51

By default this value is obtained from the specified hardware port (see above).

node_name

The node name in format: %04x-%04x-%04x-%04x.

Example:

load kgpsa_generic_storage PGA node_name=2000-0000-C923-EA51

By default this value is obtained from the specified hardware port (see above).

link_up_delay

The delay in seconds, port suspend reporting the link up waiting for Linux FC infrastructure creation. Default is 120 seconds.

Example:

load kgpsa_generic_storage PGA link_up_delay=80

link_poll_period

The link check poill interval in seconds Default is 1 second

Example:

load kgpsa_generic_storage PGA link_poll_period=2

emu_fabric

The way the emulation deals with fabric:

Value	Description
auto	Delegate to Linux if supported, otherwise emulate
no	Delegate to Linux (real physical fabric port connected too)
yes	Emulate

Example:

load kgpsa_generic_storage PGA emu_fabric="no"

lun_exclude

The list of the LUNs to be excluded. If empty (default), nothing is excluded.
No multi line is possible for this parameter; the maximum number of symbols inside the double quotes is 255. Use "lun_include" parameter instead if a lot of LUNs must be excluded to specify only the included LUNs.

Example:

load kgpsa_generic_storage PGA lun_exclude="6008-05F3-0005-2950-C758-BCC2-E88B-0007,6008-05F3-0005-2950-8B03-E26B-E231-0005"

lun_include

The list of the LUNs to be included. If empty (default), all LUNs are included.
No multi line is possible for this parameter; the maximum number of symbols inside the double quotes is 255. Use "lun_exclude" parameter instead if a lot of LUNs must be included to specify only the excluded LUNs.

Example:

load kgpsa_generic_storage PGA lun_include="6008-05F3-0005-2950-C758-BCC2-E88B-0007,6008-05F3-0005-2950-8B03-E26B-E231-0005"

scsi_version

This approach of FC emulation downgrades all attached devices to the specifically defined version of SCSI. This is done to make legacy guest operating systems happy with attached modern devices.

Value (ANSI SCSI version)	Description
any	Any version
v1	SCSI-1
v2	SCSI-2
v3	SCSI-3
v3_SPC1	SCSI-3, primary command level 1
v3_SPC2	SCSI-3, primary command level 2 (default)
v3_SPC3	SCSI-3, primary command level 3
v3_SPC4	SCSI-3, primary command level 4

Example:

load kgpsa_generic_storage PGA scsi_version="v3_SPC3"

device_id

A fake device id (if not "lp8000" is needed), the default is "0xF800" ("lp8000").

Example:

load kgpsa_generic_storage PGA device_id=0xFA00

vendor_id

A fake vendor id (if not "lp8000" is needed), the default is "0x10DF" ("lp8000").

Example:

load kgpsa_generic_storage PGA vendor_id=0x10EA

revision_id

A fake revision id (if not "lp8000" is needed), the default is "0x02" ("lp8000").

Example:

load kgpsa_generic_storage PGA revision_id=0x01

KGPSA-CA PCI Fibre Channel adapter

Table of Contents

General description

Loading KGPSA storage adapter

Configuration parameters

host_bus_location

wwid

container

media_type

removable

geometry

use_io_file_buffering

io_queue_depth

min_n_of_threads

Mapping to host resources

Fabric virtualization mode

Pass Through mode

Pass Through mode establishing sequence

Building PPT driver for EMULEX LightPulse PCI/PCI-X/PCIe FC

Installation of PPT driver for EMULEX LightPulse PCI/PCI-X/PCIe FC

Adding PPT driver for EMULEX LightPulse PCI/PCI-X/PCIe FC to Linux startup

Configuration of KGPSA-CA in pass through mode

FCMGR utility description

Configuration steps using FCMGR utility

Fabric presentation mode

FC HBA interfaces finding

List available adapters

Load HBA's kernel modules (drivers)

Discover the Linux SCSI hosts the FC HBAs are mapped to

Discover the connected FC HBAs (ports)

Discover the HBAs port/node names

Charon Configuration

By port name

By host id name

Configuration parameters

interface

trace_level

io_model

port_name

node_name

link_up_delay

link_poll_period

emu_fabric

lun_exclude

lun_include

scsi_version

device_id

vendor_id

revision_id