Contents

General Information

This section provides some basic information about AWS networking that is likely to affect Charon-SSP when running in the cloud.

The information is not comprehensive. Please refer to the Amazon AWS documentation for up-to-date and comprehensive information.

Concepts

VPC: VPC stands for virtual private cloud. It is a virtual network associated with your AWS account. It is logically isolated from other virtual networks in the AWS Cloud. You can launch your AWS resources, such as Amazon EC2 instances, into your VPC. You can specify an IP address range for the VPC, add subnets, associate security groups, and configure route tables. In addition to the default VPC, an account can have non-default VPCs. The default VPC includes an Internet gateway.

Subnet: A subnet is a range of IP addresses in your VPC. You can launch AWS resources into a specified subnet. There are public subnets that can be connected to the Internet and private subnets that have no direct Internet connection. Instances in a private subnet can reach the Internet via a NAT gateway.

Instance: An instance is a virtual machine that is launched into a VPC. It is associated with an image (e.g., Charon-SSW AMI) and a certain instance type representing the virtual hardware.

Address Assignment

Each VPC is assigned a block of private IP addresses. This block can be split by the user to form several IP subnets.

When an E2C instance is launched into the default VPC and a public subnet, the default behavior is as follows:

• If the instance has only one network interface, it is automatically assigned a private IP address and a public IP address from the address range assigned to the public subnet. This network interface is the primary network interface. It is called eth0.
• If the instance has more than one network interface, it is automatically assigned a private IP address for each of the network interfaces - but no public IP address.

The default behavior can be modified, for example:

• Manually assigning a private IP address from the subnet range.
• Enabling or disabling the automatic assignment of a private IP address to deviate from the subnet setting.
• Manually assigning a public IP address from the AWS range or the customer range.

Public IP addresses are not directly visible to the instance. The instance operating system always works with the private address. For external connections, the private address is mapped to the public IP address via NAT.

Reserved addresses (important, if manual address assignment is used):

The following addresses are reserved in each subnet and cannot be used for E2C instances (shown in the example below for network 10.1.1.0/24):

• 10.1.1.10: the network address
• 10.1.1.1: reserved by AWS for the VPC router
• 10.1.1.2: reserved by AWS in any subnet; the second host address in the base VPC network range is the DNS server for the VPC.
• 10.1.1.3: reserved by AWS for future use
• 10.1.1.255: network broadcast address; AWS networks do not use broadcasts.

An automatically assigned public IP address is released by AWS if

• a second interface with a private address is added to the instance and the instance or the network is restarted,
• a second interface with a public IP (Elastic IP) is added to the instance and the instance or the network is restarted,
• an Elastic IP address is added to the primary interface of the instance.

An automatically assigned public IP address is not persistent. Every time a instance starts, it is assigned a new public IP address. If persistent public addresses are needed, use Elastic IP addresses.

Host to Guest Communication Considerations

There are several ways a communication between the host operating system and the guest Solaris system can be implemented. For example:

1. Internal virtual bridge on the host system:
   Such a bridge has several TAP interfaces. The host and the guest systems are connected to this bridge and can communicate directly to one another. Such a communication also allows L2 traffic and modifications to the MAC address. The bridge uses its own IP subnet that can be defined by the user.
2. Communication via the AWS subnet LAN:
   In this case, a second interface is added to the Charon host system. The second interface is then assigned to the emulated guest system. After the correct configuration, the host and guest can communicate across the AWS LAN using IP. L2 protocols or any protocols that require changing the MAC address to something different than the MAC address assigned to the second interface by AWS will not work.
   To connect the guest system to the LAN, the following basic configuration steps must be performed:
   • Add the additional interface to the Charon host system.
   • Create a configuration file for the additional interface.
   • Remove the private IP address assigned to the second interface by AWS from the Linux configuration.
   • Use Charon Manager to assign the interface to the emulated SPARC system.
   • Use Charon Manager to set the MAC address of the emulated SPARC system to the same value as the one used on the host system Ethernet interface.
   • On the Solaris system, configure the private IP address that was previously assigned to the second interface on Linux.
   • Additional steps may be required:
     • If the primary interface has an automatically assigned IP address, this will be released after the first network restart with two interfaces. Hence the configuration must be changed to use a persistent Elastic IP address first to maintain reachability of the host system.
     • If both the primary and the second interface only have private IP addresses or both interfaces have public addresses (Elastic IP) assigned, separate routing tables must be created for both interfaces to enable proper routing.

The section Example of a More Complex Network Configuration provides some hints on how to configure the second interface in the different situations. Please refer to the AWS documentation for up-to-date comprehensive information.

External Communication Considerations

In addition to allowing SSH access to the host system for management purposes, it may be necessary to enable Internet communication to the host and guest system or connect host and guest to the customer's network.

Recommended way to connect the Charon host and guest systems to the customer network:

To ensure data traffic between the Charon host and guest systems and the customer network is encrypted, it is strongly recommended to use a VPN connection. An example of a simple VPN connection based on an SSH tunnel is described in SSH VPN - Connecting Charon Host and Guest to Customer Network. This connection is based on a bridge between Charon host and guest system and (via an encrypted SSH tunnel) the remote end-point in the customer network.

AWS also provides a VPN gateway instance that can be added to the customer VPC to connect the VPC to the customer network (for a charge).

Recommended way to connect the guest system to the Internet:

The Internet connection can be implemented across the VPN to the customer network. In this case, the customer can allow the guest Solaris system to access the Internet exactly following the security policies defined by the customer.

Access to the Internet from private VPC subnets:

Access to the Internet for private VPC subnets is possible across a gateway instance providing VPN access to the customer network and allowing Internet access via this path. Alternatively, a NAT gateway can be used. The NAT gateway can be implemented on a Charon host system or it can be provided by AWS for a charge.

Direct guest access to the Internet:

This is not recommended as a standard solution for security reasons. Should it be required, two interfaces with public IP addresses can be assigned to the Charon host. One of these interfaces is then dedicated to to the guest system which uses the private address interface address assigned by AWS and the MAC address of the interface assigned to the Charon host (similar to point 2 in section Host to Guest Communication Considerations above).

Guest to Guest Layer 2 Communication Considerations

Should L2 protocols be required between two guest systems on different host systems, a bridge/tunnel solution similar to the one described in SSH VPN - Connecting Charon Host and Guest to Customer Network must be set up between the two host systems to allow the L2 traffic to pass.

Further Information