| Anchor | ||||
|---|---|---|---|---|
|
| Include Page | ||||
|---|---|---|---|---|
|
...
Load network adapter (if required)
Use the "load" command as shown below.
Example:For DEC21040 adapters For Intel i8255x adapters load DE500BA/dec21x4x NICload DE602/i8255x NICNote In AlphaStation 400 configuration use the following syntax for network adapter loading:
load DE500AA/dec21x4x NIC irq_bus=isa
By default each loaded virtual network adapter uses first available PCI slot. If instead some particular slot is neded, refer refer to this section for details of specific placement of PCI peripherals on peripherals on CHARON-AXP PCI bus.Load "packet_port" or "tap_port"
Load "packet_port" or "tap_port" to connect network adapter to the host hardware network card (or to a virtual network interface).
Example:load packet_port/chnetwrk NDIS interface = "eth1"Connect the loaded "packet_port" ("tap_port") to the loaded virtual network adapter
Connect the network adapter to the "packet_port" ("tap_port") by setting the interface name.
Example:set NIC interface = NDIS
...
Each virtual network controller has the following parameters that are specified with the "set" command:
interface
| Parameter | interface |
|---|---|
| Type |
Value
Text String | |
| Value | Name of the corresponding instance of the "packet_port" or "tap_port" component |
station_address
| Parameter | station_address | ||
|---|---|---|---|
| Type | Text String | ||
| Value | The "station_address" provides the ability to configure the adapter’s permanent address. By default the adapter’s permanent address is read from the host system’s NIC. Format:
or
Example: |
|
rx_fifo_size
| Parameter | rx_fifo_size |
|---|---|
| Type | Numeric |
| Value | "rx_fifo_size" sets the receive FIFO size. The value is specified in Kb and, by default, is pre-calculated from the connected port’s size of the receive queue. Typically, you do not need to change the "rx_fifo_size" parameter. It is available for extended tuning and debugging purposes. |
adapter_mode
| Parameter | adapter_mode | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Type | Text String | |||||||||||||
| Value | Defines the link speed and the duplex settings of the virtual network adapter (except for DE602/DE602AA - see below). The values are:
Defines the link speed and the duplex settings of the virtual network adapter (except for DE602/DE602AA - see below). The values are: Example:
|
Example
...
|
...
The EIx0_MODE variable name is case insensitive, while its values are case sensitive! This is feature of OpenVMS EIDRIVER.
The values are:
| Parameter | Description |
|---|---|
| "Auto" | Auto-negotiate (default) |
| "Twisted" | 10Mbps half duplex |
| "Full" | 10Mbps full duplex |
| "Fast" | 100Mbps half duplex |
| "FastFD" | 100Mbps full duplex |
Example:
>>>set eia0_mode FastFD |
...
load packet_port/chnetwrk <instance-name> |
Example:
load packet_port/chnetwrk pp1 |
"packet_port" uses several configuration parameters to control its behavior.
...
interface
...
| class | pagebreak |
|---|
...
| Parameter | interface | ||
|---|---|---|---|
| Type | |||
interface | Text string | ||
| Value | This parameter identifies an Ethernet adapter of the host system dedicated to CHARON-AXP. Syntax:
Example:
|
port_enable_mac_addr_change
| Parameter | port_enable_mac_addr_change | |
|---|---|---|
| Type | Boolean | |
| Value | If "true" is specified (default value), CHARON-AXP sets the appropriate Ethernet address automatically. If "false" is specified, set the Ethernet address manually. Example:
|
port_retry_on_tx
| Parameter | port_retry_on_tx | |
|---|---|---|
| Type | Numeric | |
| Value | The "port_retry_on_tx" parameter controls the number of times a port will attempt to transmit a packet before giving up. By default, the value is 3. Increasing this value may introduce problems in carrier loss logic, because not all NIC drivers support a carrier status query. Typically, you do not need to increase the value. Example:
|
port_pending_rx_number
| Parameter | port_pending_rx_number | |
|---|---|---|
| Type | Numeric | |
| Value | The "port_pending_rx_number" parameter sets the number of pending receive buffers. The default value is 63. The maximum value allowed is 195. You may want to increase the "port_pending_rx_number" when you have very busy networking and experience problems like losing connections not related to the carrier loss. Typically, you do not need to change this parameter. Example:
|
port_pending_tx_number
| Parameter | port_pending_tx_number | |
|---|---|---|
| Type | Numeric | |
| Value | The "port_pending_tx_number" parameter sets the number of buffers the port uses to transmit. The default value is 62. You may want to increase the "port_pending_tx_number" value if the log file indicates dropped TX packets due to TX queue overflow. Typically, you do not need to change this parameter. Example:
|
...
| class | pagebreak |
|---|
...
Example
...
|
...