Page Comparison

Anchor

	TopUtilPage
	TopUtilPage

...

<source disk file name> - a file name of the disk image to be transferred
<source disk parameters> - the name of the disk from the list of available on "mkdskcmd --list" request or the disk geometry specification (see below).
--shrink or -k - used in the case when the target disk is transferred to a smaller disk.

Example:

$ mkdskcmd --transfer /etc/rz22.vdisk rz25

It is also possible to specify the disk parameters manually with "--blcount / -c" (blocks count) and "--blsize / -z" (blocks size) switches:

$ mkdskcmd --transfer <source disk file name> -blsize <number> -blcount <number>

Example:

$ mkdskcmd -t /etc/custom.vdisk -z 512 -c 262134

...

$ mtd <tape container name> <tape device name>

Example:

$ mtd /charon/tapes/tape1.vtape /dev/st5

...

Run "hasp_srm_view" utility on the "RecipientHost" with the following parameters to collect the host ID info:
$ hasp_srm_view -idf
The "recipient.id" file will be created in the current directory.
Copy the "recipient.id" file to the "SourceHost".
Info
"recipient.id" is an ASCII file, so use the "ascii" option for FTP transfer.
On the "SourceHost", open the "Sentinel Admin Control Center" (ACC) ( http://localhost:1947). Note the number of the software license you are going to transfer.
Run the "hasp_srm_view" utility in the following way to create a transfer license for the host "RecipientHost":
$ hasp_srm_view -tfr <license number> recipient.id
The "license number" is the value collected at the step 3.
Example of collecting a transfer license:
$ hasp_srm_view -tfr 12345678 recipient.id
A "<license number>.v2c" file will be created in the current directory. In the example above, the name of the transfer license will be "12345678.v2c"
Div
class pagebreak
Copy the resulting "<license number>.v2c" file to the "RecipientHost".
Info
"<license number>.v2c" is an ASCII file, so use the "ascii" option for FTP transfer.
On the "RecipientHost", open "Sentinel Admin Control Center" (ACC) (http://localhost:1947) and apply the "<license number>.v2c" file as described above.

...

Open "Sentinel Admin Control Center" (ACC) (http://localhost:1947). Note the number of the software license you are going to remove.
Run the "hasp_srm_view" utility in the following way to remove the license:
$ hasp_srm_view -tfr <license number>
The "license number" is the value collected at the step 1.
Example:
$ hasp_srm_view -tfr 12345678
The "<license number>.v2c" file will then be created in the current directory. In the example above the name of the transfer license will be "12345678.v2c"
It is always possible to re-apply the created ".v2c" file to restore the deleted software license.

Back to Table of Contents

...

Parameter	Value	Description
<option>	u	Updates a Sentinel protection key / attaches a detached license
	i	Retrieves Sentinel protection key information
	d	Detaches a license from a Sentinel Software License (SL) key
	r	Rehost a license from a Sentinel Software License (SL) key
	h	Display help
[filename]		Path to the V2C/H2R file (in case of 'u'pdate/attach)
[filename]		Path to the C2V file Optional: uses "stdout" if file name is not specified (in case of 'i'nfo)

Example:

# hasp_update u license_update.v2c

...

The utility allocates chosen network interfaces (both physical and virtual) and configures the offload parameters.

Note
The NetworkManager service must be running in order to have all the functionalities enabled with "ncu". If the service is not enabled please configure the network using the manual operations described in the section "Manual configuration of CHARON networking" of the Installation chapter of this Guide.

Dedication of a host physical interface to CHARON

...

Login a root. Start "ncu" utility:

# ncu

CHARON Network Configuration Utility, STROMASYS (c) 2015 Version 1.5

Interfaces   Dedicated to    State
----------   ------------    ------------
eth0         host            connected to host
eth1         bridge          connected to bridge
lo           host            unmanaged from host
tap0         bridge          connected to bridge
tap1         bridge          connected to bridge

==================================================================
bridge name     bridge id           STP enabled        interfaces
br0_eth1        8000.525400698995a  no                 tap0
                                                       tap1

select action:
1 - Dedicate to CHARON
2 - Release to host
3 - Create Bridge with TAPs
4 - Remove Bridge
5 - Print status
6 - Exit
:> 4

...

Versions Compared

Old Version 4

New Version Current

Key

Dedication of a host physical interface to CHARON