Versions Compared

Old Version 2

changes.mady.by.user W.Erber

Saved on

compared with

New Version Current

changes.mady.by.user W.Erber

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Anchor
TOC
TOC
Include Page
KBCOMMON:KB-CSSstyle
KBCOMMON:KB-CSSstyle

This option is currently only supported for Charon-SSP AL images version 5.3.8 or higher on selected cloud marketplaces.

The AutoVE mode is an extension of the Automatic Licensing configuration available for selected cloud marketplaces.

...

  • At the time of writing, AutoVE mode for Charon products is only available when using an Automatic Licensing (AL) Charon-SSP marketplace image on AWS, GCP, OCI, or Azure (minimum version 5.3.8) to create a Charon host instance. Please contact your Stromasys representative to get details on the availability of such marketplace images in your cloud environment.
  • The AutoVE license server information must be configured before the Charon host instance is first launched. The information can be changed later, but once the host system has connected to a public license server in the selected cloud, it cannot be reconfigured to use an AutoVE server (and vice-versa).

Changed license server selection in Charon-SSP AL images starting with SSP version 5.6.8:

Starting with version 5.6.8, the license server selection in cloud-specific AL images has changed to simplify the operation of the SSP Amazon Linux AMI used in the new AWS service.

Case 1: user provides no license server information in the instance user data at initial instance launch:

a) If the file /opt/charon-license-server exists and contains valid AutoVE server information, the cloud instance will use the AutoVE license servers specified in the file. This file exists by default in the SSP Amazon Linux AMI where it points to the public, Stromasys-operated AutoVE license servers specific to this AWS service. Such public AutoVE servers are only available in AWS at the time of writing.

b) If the file does not exist, the cloud instance will use the public, Stromasys-operated license servers (AL mode).

Case 2: user provides AutoVE license server information in the instance user data at initial instance launch.

The cloud instance will use the private, customer-operated AutoVE license servers.

The following sections will discuss the AutoVE configuration for a Charon host system:

...

Configuring the AutoVE Server Information at AWS Instance Launch

Excerpt
nameAWSUserData

Please note:

  • Should you use the SSP Amazon Linux AMI with SSP version 5.6.8 or higher as provided by the AWS Mainframe Modernization - Virtualization for SPARC service, the instance will by default connect to the public, Stromasys-operated AutoVE license servers (defined in /opt/charon-license-server ). You only need the user data definition for older versions or to override the default with your private AutoVE servers.
  • The example below shows the appearance of the AutoVE license server information that is entered as User Data in the Advanced Details configuration section
in the Configure
  • at the bottom of the Launch an Instance window during the initial configuration of an instance. Scroll down to the bottom of the configuration window to open and display the user data section in the Advanced Details.
  • In the older GUI version, the Advanced Details section is part of the Configure Instance window - the layout is somewhat different, but the configuration options are the same.

 Enter the information for the AutoVE license server as shown in the example below .Image Removed(it shows the public AutoVE servers):

Image Added

Valid User Data configuration options:

  • primary_server=<ip-address>[:<port>]
  • backup_server=<ip-address>[:<port>]

where

  • <ip-address> stands for the IP address of the primary and the backup server as applicable, and
  • <port> stands for a non-default TCP port used to communicate with the license server (default: TCP/8083).

Please note: at least one license server must be configured at initial launch to enable AutoVE mode. This can be via the /opt/charon-license-server file with the default public servers (SSP 5.6.8 or higher) or via the manual user data configuration. Otherwise, the instance will bind to one of the public AL license servers operated by Stromasys.

...

Excerpt
nameGCPUserData

The AutoVE license server information is entered as Custom Metadata. In the initial instance configuration window, go to the bottom where the NETWORKING, DISKS, SECURITY, MANAGEMENT... configuration section is located. Open it and select the Management section. Add the Custom Metadata as shown in the example below:

Valid User Data configuration options:

  • primary_server =<ip-address>[:<port>]
  • backup_server=server  <ip-address>[:<port>]

where

  • <ip-address> stands for the IP address of the primary and the backup server as applicable, and
  • <port> stands for a non-default TCP port used to communicate with the license server (default: TCP/8083).

Please note: at least one license server must be configured at initial launch to enable AutoVE mode. Otherwise, the instance will bind to one of the public license servers operated by Stromasys.

...

  • In the GCP management console, open the details window of your Charon host instance.
  • Klick Click on the Edit symbol at the top of the page.
  • Scroll down to the Custom Metadata section.
  • Modify the AutoVE configuration as needed and click on Save at the bottom of the page.
  • Activate the changes:
    • After cleanly shutting down any running guest operating systems, restart the emulator instances and any required guest systems. It can take a minute or two until the change becomes active.
    • If changes are made to the VE license server configuration (e.g., changing the port numbers), the VE license server must also be restarted.

...