Table of contents

Serial

...

Lines for Emulated Systems

Most models emulated by Charon-PAR have two serial lines (LDev 20 and 21). One of these emulated lines is mapped to the serial console, the other to a second serial port. Some models may have more serial lines. Please refer to Emulated Model Hardware Configuration Details for more information. This section provides an overview of the serial line configuration. Please also refer to the Configuration File Reference.

Configuration Parameters Overview

Each emulated line has a device path denoting bus and slot information in the emulated system (see configuration file template or chapter Emulated Model Hardware Configuration Details) and a configuration path. The configuration path is used to set up the serial line configuration in the emulator configuration file.

The following table shows the device and configuration paths used for the two serial lines:

...

Serial port configuration options are specified using the following syntax:

A serial port has three configuration options:

...

The serial port type determines the protocol used on the serial port. Possible values are:

• socket: the port is set to raw mode.
• telnet: the port supports the telnet protocol.
• device: indicates that the emulated serial line is connected to a physical terminal on the host.

...

Each port is mapped to a TCP socket on the emulator host or to a physical line. This parameter defines the port number used or the name of the physical device. The port number must be unique on the host system.

A port number is specified as: ":<portnumber>". It requires a port type of socket or telnet.

Default values:

• ":30000" for line 1
• ":30002" for line 2

A physical device is specified as "<device-file>". It requires a port type of device.

Example:

• "/dev/ttyS0"
• "/dev/ttyUSB0"

...

The configuration file templates are set up with the following default configurations:

...

serial.uart0.device.type="telnet"
serial.uart0.device.port=":30000"
serial.uart0.device.command="putty -load HPA-Telnet-VT100"

...

Terminal Emulation Considerations

The emulated serial lines can be accessed vial a terminal emulation program running on the emulator host system or on a remote system. 

Please note: if the terminal emulation program runs on a remote system, any firewall between the remote system and the emulator host system must permit the configured ports.

Stromasys supplies PuTTY profiles with the Charon-HPA kit. However, customers can select another terminal emulation program better suited to their purposes. This is especially true for emulated HP3000 systems, where applications often use block mode terminals. This mode is not supported by PuTTY.

If not done so already during the installation, copy the provided PuTTY profiles to the correct directory on the host system. See Charon-HPA Software Installation.

Accessing Emulated HP3000 Systems via Terminal Emulation

HP3000 guest systems running on Charon-HPA can be accessed directly from the Linux emulator host using either of two freeware terminal emulators listed below, both of which run directly on the Linux host desktop, or by simply using the telnet command. Each has limitations, however. Neither terminal emulator provides a reliable way to paste multiple lines of text into :EDITOR , for example.
Once the HP3000 network is configured, it's preferable to connect to the virtual HP3000 from a networked PC using any of the robust commercially-available terminal emulators.

Using PuTTY

The PuTTY terminal emulator is the preferred method to use as the HP3000 console. It does not, however, support HP terminal escape sequences, so any inverse or highlighted text codes will be ignored, and block mode applications cannot be run. Using PuTTY in telnet mode (as supplied) allows use of the Break key. PuTTY supports copy and paste. To copy text to the clipboard, just select it with the left mouse button (this automatically copies the selection to the clipboard). To paste the clipboard into a PuTTY window, use Shift-Ins . Unfortunately, PuTTY cannot be used to reliably paste large blocks of text (even with MPE type-ahead enabled), as data overruns can easily occur.

...

By default, the emulator configuration is set up to start PuTTY on the console port with the command:

serial.uart0.device.command="putty -load HPA-Telnet" (default port 30000). 

To start an terminal emulator manually, perform the following steps:

...

$ putty -load HPA-Telnet

...

Start PuTTY from the command-line.

$ putty

Select and load the required profile.
Select Fonts on the left and select a monospace font.
Select Session on the left and save the profile.

...

Start PuTTY from the command-line.

$ putty

Select and load the required profile.
Change the hostname to the one of the Charon-HPA host as required.
Connect to the remote Charon-HPA system.

The image below shows a PuTTY terminal window connected to the emulated HP3000 system console:

Image Removed

...

Using xhpterm

The xhpterm terminal emulation (an X Windows version of freevt3k ) does not support many HP terminal escape sequences, but it can be used to run block-mode applications. It must be used on a serial line set up for raw mode.

The following image shows an xhpterm window connected to the second serial line of an emulated HP3000 system (running NMMGR):

Image Removed

Mapping the Block-Mode Enter key

The primary purpose for including this terminal emulator is to allow block-mode applications (like NMMGR ) to be run from the Linux desktop. xhpterm uses the numeric keypad Enter key to simulate block-mode Enter. If your keyboard does not have a numeric key pad, the Enter key can be mapped to another key or key combination using xmodmap on Linux. 

Example mapping the numeric key pad Enter key to Right-Ctrl:

...

$ xmodmap -pk | grep "Control_R"

You will receive an output similar to: 

105 0xffe4 (Control_R) 0x0000 (NoSymbol) 55 0xffe4 (Control_R)

...

Using Different Fonts

The default command-line to start xhpterm is:  $ xhpterm -port 30000 -clean -font 10x20

If the 10x20 font is not found, you can try -font 6x13 instead.

Additional fonts (e.g. the 9x15 font) can be installed using the command

...

 When using xhpterm , avoid resizing the window - it can result in input and output fields in block-mode programs being misaligned. Changing the screen font will change the window size automatically, without causing this problem.

...

If the Super/IO module has been loaded, there are two additional serial lines. In the configuration, they are identified by 

• superio_001.uart0 and
• superio_001.uart1.

The basic configuration options are the same as for the default serial lines.

The most important configuration options are listed below. For additional parameters and more detailed information, please refer to the Configuration File Reference.

The configuration file templates contain the following default configurations:

HP-UX Interactive Login Activation

To enable interactive login on a non-console serial line in HP-UX, a GETTY process has to be started for the terminal line.

You can add an additional terminal via SAM  (Peripheral Devices > Terminals and Modems > Actions > Add Terminal). This will also add the necessary entries in to /etc/inittab.

You can also (as the root user) edit /etc/inittab to add the configuration manually or to modify an existing configuration. After editing the file, any changes must be activated by running the command 

# init q

The command 

# ps -ef | grep -i getty 

can be used to verify that the processes are running. Note that a GETTY process is only shown for lines without active login session.

Sample inittab entries:

a0:1234:respawn:/usr/sbin/getty -h tty1p0 9600
a1:3:respawn:/usr/sbin/getty -h tty2p0 9600

After this configuration, when connecting to the serial line, a login prompt should be displayed.

Terminal Emulation Considerations

The emulated serial lines can be accessed via a terminal emulation program running on the emulator host system or on a remote system. 

Please note: if the terminal emulation program runs on a remote system, any firewall between the remote system and the emulator host system must permit the configured ports.

Stromasys supplies PuTTY profiles with the Charon-PAR kit. However, customers can select another terminal emulation program better suited to their purposes. This is especially true for MPE/iX guest systems where applications often use block mode terminals. This mode is not supported by PuTTY.

If not done so already during the installation, copy the provided PuTTY profiles to the correct directory on the host system. See Post-Installation Tasks in  Charon-PAR Software Installation.

Accessing Emulated Charon-PAR/PA3 Systems via Terminal Emulation

Charon-PA3 guest systems can be accessed directly from the Linux emulator host using either the PuTTY or xhpterm terminal emulator described below, both of which run directly on the Linux host desktop, or by simply using the telnet command. Each has limitations, however. Neither terminal emulator provides a reliable way to paste multiple lines of text into :EDITOR , for example.
Once the network of the Charon-PAR/PA3 guest system has been configured configured, it may be preferable to connect to the emulated system from a networked PC using any of the robust commercially-available terminal emulators.

Using Non-Graphical Telnet Client

In the absence of a graphical user environment, terminal emulators such as PuTTY and xhpterm cannot be used. In such cases, you can use the telnet command on the Charon host or from a remote system to access the serial console port of the emulated PA3 system.

The basic command syntax is as follows:

$ telnet <charon-host> <console-tcp-port>

Parameters:

• charon-host: IP address or hostname of the Charon-PAR host system on which the emulator runs
• console-tcp-port: The TCP port configured for the serial console port in the configuration file of the emulated PA3 system

Please note: Line-editing is very limited. To delete a character on the command-line, use CTRL+BACKSPACE. Note that the deleted character will still be visible until it is overwritten. Block-mode applications are not supported.

Using PuTTY

The PuTTY terminal emulator is the preferred method to use as the Charon-PAR/PA3 console. It does not, however, support the terminal escape sequences used by the legacy hardware, so any inverse or highlighted text codes will be ignored, and block mode applications cannot be run. Using PuTTY in telnet mode (as supplied) allows use of the Break key. PuTTY supports copy and paste. To copy text to the clipboard, just select it with the left mouse button (this automatically copies the selection to the clipboard). To paste the clipboard into a PuTTY window, use Shift-Ins . Unfortunately, PuTTY cannot be used to reliably paste large blocks of text (even with MPE type-ahead enabled), as data overruns can easily occur.

By default, the emulator configuration is set up to start PuTTY on the console port with a command similar to the following example:

serial.uart0.device.command="putty -load PAR-Telnet" (default port 30000). 

To start an terminal emulator manually, perform the following steps:

The image below shows a PuTTY terminal window connected to the guest MPE/iX system console:

Image Added

Please note: Line-editing is very limited. To delete a character on the command-line, use BACKSPACE. Note that the deleted character will still be visible until it is overwritten. Block-mode applications are not supported.

Using xhpterm

The xhpterm terminal emulation (an X Windows version of freevt3k ) does not support many terminal escape sequences used by historic PA-RISC hardware for MPE/iX, but it can be used to run block-mode applications. It must be used on a serial line set up for raw mode.

Sample command (run on Charon host): /opt/charon/bin/xhpterm -port 30002 -clean -font 10x20

The following image shows an xhpterm window connected to the second serial line of an emulated MPE/iX system (running NMMGR):

Image Added

Working without Block-Mode Enter key

If working without a block-mode Enter key, you can navigate using the function keys of your keyboard. They correspond to the selection fields at the bottom of the screen.

For example, in the above window,

• F1 would correspond to Open Config,
• F8 would correspond to Exit Program.

Mapping the Block-Mode Enter key

The primary purpose for including this terminal emulator is to allow block-mode applications (like NMMGR ) to be run from the Linux desktop. xhpterm uses the numeric keypad Enter key to simulate block-mode Enter. If your keyboard does not have a numeric key pad, the Enter key can be mapped to another key or key combination using xmodmap on Linux. 

Example mapping the numeric key pad Enter key to Right-Ctrl:

Using Different Fonts

The default command-line to start xhpterm is:  $ xhpterm -port 30000 -clean -font 10x20

If the 10x20 font is not found, you can try -font 6x13 instead.

Additional fonts (e.g. the 9x15 font) can be installed using the command

Please note: When using xhpterm , avoid resizing the window - it can result in input and output fields in block-mode programs being misaligned. Changing the screen font will change the window size automatically, without causing this problem.

Accessing Emulated Charon-PAR/PA9 Systems via Terminal Emulation

Using Non-Graphical Telnet Client

In the absence of a graphical user environment, terminal emulators such as PuTTY and xhpterm cannot be used. In such cases, you can use the telnet command on the Charon host or from a remote system (if the serial line configuration permits it) to access the serial console port of the emulated PA3 system.

The basic command syntax is as follows:

$ telnet <charon-host> <console-tcp-port>

Parameters:

• charon-host: IP address or hostname of the Charon-PAR host system on which the emulator runs
• console-tcp-port: The TCP port configured for the serial console port in the configuration file of the emulated PA3 system

Please note: To make character deletion via the BACKSPACE key work on the command-line of HP-UX, you may have to enter the command$ stty erase <backspace-key> (and add it to your shell startup file, e.g., $HOME/.profile).

Using PuTTY

Stromasys provides preconfigured PuTTY profiles to access the serial console of an HP-UX system running on Charon-HPAPAR. PuTTY does not support all control characters used by HP-UX, but many utilities (e.g., SAM) will work with some restrictions.

By default, the emulator configuration is set up to start PuTTY on the console port with the command: seriala command similar to the following example: 
   serial.uart0.device.command="putty -load HPAPAR-Telnet-VT100".

To start an terminal emulator manually, perform the following steps:

...

Instead of PuTTY, you can also use the standard telnet command on your local or remote Linux system (telnet <charon-par-host> <port>). However, Stromasys does not provide profiles for this. To make character deletion via the BACKSPACE key work on the command-line of HP-UX, you may have to use the command $ stty erase <backspace-key>.

Additional configuration steps to improve the behaviour behavior of the terminal emulation:

The following image shows a PuTTY window running SAM after the settings above were configured:

Image Removed

The following image shows a PuTTY window where the locale on the system running PuTTY is something different from C:

Image RemovedAdditional information: Cannot get correct line drawing on Linux/UNIX with Putty.

Other Terminal Emulation Considerations

Accessing the Emulated System Console from a Remote System

 Please Please note:

• The serial line port configuration must allow the remote connection.
• intermediate firewalls must allow the ports used.

...

• There can be only one connection to an emulated serial line at one time.

The following two options provide two examples of how to connect to the console of an emulated system from a remote system.

...

If PuTTY is installed on the remote system, you can use the session profiles provided by Charon-HPA PAR (copy them from the emulator host) to connect to the emulated system:

...

To exit the session, use the telnet escape key sequence CTRL+} and type quit.

Tunneling a Terminal Emulation through an SSH Tunnel

Even though a plain telnet connection can be used to connect to the emulated system's console, this plaintext connection may create security problems. As an alternative, you can tunnel a terminal emulation through an SSH tunnel provided X11 is active on the emulator host and the remote system.

 Any Please note: Any intermediate firewall must permit the port used for SSH (default 22).

...

...