| Anchor | ||||
|---|---|---|---|---|
|
| Include Page | ||||
|---|---|---|---|---|
|
...
It is strongly recommended to use only physical network adapters for CHARON-AXP networking to gain maximum performances. In situations where the host has only one network adapter, you can use Linux virtual network Interfaces ("TUN/TAP") and map individual CHARON-AXP instances to their own virtual interfaces.
There are 2 ways to create the Linux virtual network Interfaces ("TUN/TAP"):
- Using the "ncu" utility
- Manually
...
This can be done using the ncu utility.
It is also possible to perform the operations manually. Refer to your Operating System Network Administration guide for details.
| Note |
|---|
On Red Hat Enterprise Linux 6 & 7 and CentOS 7, the following packages are needed:
On Red Hat Enterprise Linux 8 and CentOS 8, the following packages is needed:
|
Using "ncu" utility to establish CHARON virtual network
Login as root and start the "ncu" utility:
CHARON Network Configuration Utility, Version 1.6. Copyright STROMASYS (Cc) 2014-20192020 STROMASYSVersion SA1. 7
|
...
Enter "8" to quit the "ncu" utility.
...
Manual configuration of CHARON virtual network
Host preparation
...
.
...
# ifconfig eth<N> 0.0.0.0 promisc up
...
In case the firewall is enabled on the host system, the following command should be executed to allow the bridge to forward IP packets.
Red Hat Enterprise Linux 6.x:
...
# /sbin/iptables -I FORWARD -m physdev --physdev-is-bridged -j ACCEPT
This command can also be performed from the bridge configuration script. It has to be executed each time the iptables service is (re)started.
It is also possible to make this setting system-wide. Either:
...
Issue the given command from the firewall control panel.
Add the following line to the end of the "/etc/sysconfig/iptables" file:
...
-I FORWARD -m physdev --physdev-is-bridged -j ACCEPT
Red Hat Enterprise Linux 7.x and CentOS 7.x (the '>' sign below is the continuation line character):
...
# firewall-cmd --permanent --direct --add-rule ipv4 filter INPUT 1 -m physdev --physdev-is-bridged \
> -j ACCEPT
# firewall-cmd --permanent --direct --add-rule ipv6 filter INPUT 1 -m physdev --physdev-is-bridged \
> -j ACCEPT
# firewall-cmd --reload
...
Virtual interface creation
The creation of the desired number of virtual network interfaces (TAPs) can be performed in the following way:
...
# tunctl [-t tap<N>]
where “tap<N>” is a name of an instance of the virtual network interface, i.e. “tap0”, “tap1” etc.
Once each virtual network interface instance is created it must be set to promiscuous mode:
...
# /sbin/ifconfig tap<N> promisc up
...
| class | pagebreak |
|---|
Bridge creation
To interconnect the physical and virtual network interfaces created in the previous step, the network bridge must be introduced in the following way:
...
# /usr/sbin/brctl addbr br0
where “br0” stands for a name of the created bridge.
Now it is possible to add the network interfaces to the created bridge:
...
# /usr/sbin/brctl addif br0 eth<N>
# /usr/sbin/brctl addif br0 tap0
…
# /usr/sbin/brctl addif br0 tap<N>
...
# /usr/sbin/brctl addif br0 eth1
# /usr/sbin/brctl addif br0 tap0
The proposed configuration assumes one and only one network bridge so loops are not possible. It is required to turn off the spanning tree protocol with the following command:
...
# /usr/sbin/brctl stp br0 off
...
Starting bridge
To start the created bridge “br0”, use the following command:
...
| Include Page | ||||
|---|---|---|---|---|
|
Usage of the virtual interface in CHARON-AXP configuration
Once the “tap<N>” interfaces have been created, the load command maps those interfaces to CHARON-AXP:
|
| Include Page | ||||
|---|---|---|---|---|
|