| Anchor | ||||
|---|---|---|---|---|
|
| Include Page | ||||
|---|---|---|---|---|
|
...
| Table of Contents | ||||
|---|---|---|---|---|
|
All Linux and HP-UX sample commands in this section are performed as the root user (prompt = #). This may not be necessary for all commands in all environments depending on the local permission settings. The commands can be executed on the Charon host graphical console or via a non-graphical login (e.g., SSH). However, for accessing the running emulator, the use of PuTTY is strongly recommended because it works best with the emulator environment.
The Charon-PA9 functionality of Charon-PAR emulates the historic HP9000 hardware.
HP-UX ISO Installation Medium
...
| Step | Command | |
|---|---|---|
| 1 | Change to the directory where you store your virtual disks. | # cd /data/Stromasys/host1/Data/Disk/ |
| 2 | Create an empty disk container. Note that the actual size of the disk will depend on the requirements of your emulated system. The disk name shown is just an example.
| # dd if=/dev/zero of=ldev1.dsk bs=1K count=2091520 |
| Div | ||
|---|---|---|
| ||
Adapting the Configuration File Template
...
| Step | Description | |
|---|---|---|
| 1 | Create a copy of the configuration file template. | Example:
|
| 2 | Open the configuration file in a text editor. |
or
|
| 3 | Configure the system model. | model "720" Configured model must be covered by your license. |
| 4 | Configure the RAM for the emulated system (in MB). | memory 64 |
| 5 | Configure the serial console for telnet via PuTTY. | Use the method 2 of the serial line section in the configuration file and make sure the definition of the asp.uart0.device is:
|
| 6 | Configure disk 1 (system disk). | Change definition of DKA0 to:
|
| 7 | Add a definition for disk 2 (ISO file) or (if it already exists) modify the definition to point to your ISO installation file for the mini-system (the install disk). |
|
| 8 | Configure a network card. | Change definition of the Ethernet interface configuration to the interface that is assigned to the emulated system (example: eth1) and disable the offload parameters for the interface:
|
| 9 | Save the configuration file. |
| Div | ||
|---|---|---|
| ||
Starting the Emulated System and Installing the Guest System
...
- Press the Enter key.
- This should produce the prompt Main Menu: Enter command or menu >.
- Enter the command
boot 2/0/1.1.0to boot from the ISO and confirm by pressing the Enter key. - At the prompt Interact with IPL (Y or N)?> answer N.
- At the next prompt, select VT100 as the terminal.
| Div | ||
|---|---|---|
| ||
HP-UX 9.07 Installation Phase 1: Installing the Basic System
During this phase, a basic system is installed to the root disk that will enable the installation of the rest of the operating system.
After booting the install ISO file as described above, you will eventually see an overview of the installation steps:
After you've read the information, press any key to continue with the next step: the root disk selection.
The following image shows a sample:
In the above sample, select the offered disk by entering its number and press Return.
Before the installation starts, you have to select if the root disk should support long file names:
...
Type exit at the pa9-32> prompt to stop the emulator.
| Div | ||
|---|---|---|
| ||
HP-UX 9.07 Installation Phase 2: Installing the Operating System Filesets
...
- Confirm that you have the correct ISO installed.
- Enter your choice for the fileset selection (normally all filesets of the Core OS).
- You will be asked to confirm your choice twice.
- Then, the loading of the filesets begins.
- At the end, the HP-UX system is shut down and returns to the console environment.
| Div | ||
|---|---|---|
| ||
HP-UX 9.07 Installation Phase 3: Booting and Configuring the HP-UX Operating System
...