Page Comparison

#
# Copyright (C) 1999-2019 2018 STROMASYS
# All rights reserved.
#
# The software contained on this media is proprietary to and embodies the
# the confidential technology of STROMASYS. Possession, use, duplication, or
# or dissemination of the software and media is authorized only pursuant to a
# to a valid written license from STROMASYS.
#
#============================================================================
#
# Sample configuration file for AlphaServer DS20 machines.
#
#----------------------------------------------------------------------------

set session hw_model = AlphaServer_DS20

#============================================================================
#
# Choose a name for the instance, if needed, to differentiate it among other
# instances running on the same host.
#
#----------------------------------------------------------------------------

#set session configuration_name = AlphaServer_DS20

#============================================================================
#
# Use the following commands to disable the rotating LOG files and enable
# a single LOG file. Select either append or overwrite (for each time the
# instance starts) and specify desired log path and file name.
#
#----------------------------------------------------------------------------

set session log_method = append
#set session log_method = overwrite
#set session log = AlphaServer_DS20.log

#============================================================================
#
# Overrides system assigned process's CPU affinity. The session changes
# the process's CPU affinity to the one specified.
#
#----------------------------------------------------------------------------

#set session affinity="0, 1, 2, 3"

#============================================================================
#
# The 'n_of_io_cpus' option overrides number of host CPU cores reserved for
# I/O processing. If omitted the session reserves 33% of available host CPU
# cores for I/O processing. Note that total amount of available host CPU
# cores is determined based on process's CPU affinity.
#
#----------------------------------------------------------------------------

#set session n_of_io_cpus=1
#set session n_of_io_cpus=2
#set session n_of_io_cpus=...

#============================================================================
#
# AlphaServer DS20 6/500
#
#----------------------------------------------------------------------------

#set ace cpu_architecture = EV6
#set rom dsrdb[0] = 1920 system_name = "AlphaServer DS20 6/500"

#============================================================================
#
# AlphaServer DS20E 67/667
#
#----------------------------------------------------------------------------

set ace cpu_architecture = EV67
set rom dsrdb[0] = 1940 system_name = "AlphaServer DS20E 67/667"

#============================================================================
#
# The 'n_of_cpus' option reduces number of emulated Alpha CPUs in the
# configuration.
#
#----------------------------------------------------------------------------

#set session n_of_cpus=1

#============================================================================
#
# Override default System Serial Number.
#
#----------------------------------------------------------------------------

#set rom system_serial_number = SN01234567

#============================================================================
#
# Specify size of RAM from 256MB up to 32768MB (32GB) in 256MB extents.
#
#----------------------------------------------------------------------------

#set ram size=256
#set ram size=512
#set ram size=1024
#set ram size=4096
#set ram size=32768

#============================================================================
#
# Uncomment to allow the virtual SRM console environment be preserved across
# emulator restarts.
#
#----------------------------------------------------------------------------

#set rom container="AlphaServer_DS20.bin"

#============================================================================
#
# Uncomment to allow saving CMOS NVRAM content, so that to preserve
# Time & Date information.
#
#----------------------------------------------------------------------------

#set toy container="AlphaServer_DS20.dat"

#============================================================================
#
# Select the connection method for the console serial line OPA0.
#
#----------------------------------------------------------------------------

#set COM1 alias = OPA0 line = "/dev/ttyN"
#set COM1 alias = OPA0 port = 10003
#set COM1 alias = OPA0 port = 10003 application = "xterm -title OPA0 -e telnet 127.0.0.1 10003"
#set COM1 alias = OPA0 port = 10003 application = "xterm -title OPA0 -e chterm -h 127.0.0.1:10003"
set COM1 alias = OPA0 line = (console)

# ... fallback to legacy mode ...
#load physical_serial_line OPA0 line = "/dev/ttyN"
#load virtual_serial_line OPA0 port = 10003
#load operator_console OPA0

#----------------------------------------------------------------------------
#
# Uncomment to allow 'F6' to terminate the running emulator. Closing console
# satellite application may also be used for that.
#
#----------------------------------------------------------------------------

#set OPA0 stop_on = "F6"
#set OPA0 stop_on = "Application"
#set OPA0 stop_on = "F6, Application"

#============================================================================
#
# Select connection for the serial line TTA0.
#
#----------------------------------------------------------------------------

#set COM2 alias = TTA0 line = "/dev/ttyN"
#set COM2 alias = TTA0 port = 10000
#set COM2 alias = TTA0 port = 10000 application = "xterm -title TTA0 -e telnet 127.0.0.1 10000"
#set COM2 alias = TTA0 port = 10000 application = "xterm -title TTA0 -e chterm -h 127.0.0.1:10000"

#============================================================================
#
# Improve granularity of emulated AXP timer.
#
#----------------------------------------------------------------------------

#set isa clock_period = 1000

#============================================================================
#
# Uncomment to connect the emulator's DQA0 to host's ATAPI CD/DVD-ROM drive.
#
#----------------------------------------------------------------------------

#set ide container = "/dev/sg<N>"

#============================================================================
#
# Enable support for AlphaStation Sound Card (AD1848).
#
#----------------------------------------------------------------------------

#load PCXBJ AUA

#============================================================================
#
# Load optional DE500BA PCI Ethernet Adapter (EWA).
#
# TIP: You need to uncomment the "load DE500BA ..." line and one of the
# "load packet_port ..." lines below to attach the EWA to host NIC (or not)
#
#----------------------------------------------------------------------------

#load DE500BA EWA interface = EWA0

# choose this one to leave EWA unconnected
#load packet_port EWA0 interface = "(disabled)"

# ===choose this one to connect EWA to host's NIC (by its name)
#load packet_port EWA0 interface = "eth<N>"

#============================================================================
#
# Load another optional DE500BA PCI Ethernet Adapter (EWB).
#
# Attach the EWA to the host's NIC.TIP: You need to uncomment the "load DE500BA ..." line and one of the
# "load packet_port ..." lines below to attach the EWB to host NIC (or not)
#
#----------------------------------------------------------------------------
#set EWA0

#load DE500BA EWB interface = EWB0

# choose this one to leave EWB unconnected
#load packet_port EWB0 interface = "eth<N>(disabled)"

# ==choose this one to connect EWB to host's NIC (by its name)
#load packet_port EWB0 interface = "eth<N>"

#============================================================================
#
# Load another optional DE500BA PCI Ethernet Adapter (EWBEWC).
#
# TIP: You need to uncomment the "load DE500BA ..." line and one of the
# "load packet_port ..." lines below to attach the EWC to host NIC (or not)
#
#----------------------------------------------------------------------------

#load DE500BA EWB EWC interface = EWB0EWC0

# choose this one to leave EWC unconnected
#load packet_port EWB0 EWC0 interface = "(disabled)"

# ============================================================================
#
# Attach the EWB to the host's NIC.
#
#----------------------------------------------------------------------------
#set EWB0 interface = "eth<N>"
#============================================================================
#
# Load another optional DE500BA PCI Ethernet Adapter (EWC).
#
#----------------------------------------------------------------------------
#load DE500BA EWC interface = EWC0
#load packet_port EWC0 interface = "(disabled)"
#============================================================================
#
# Attach the EWC to the host's NIC.
#
#----------------------------------------------------------------------------
#set choose this one to connect EWC to host's NIC (by its name)
#load packet_port EWC0 interface = "eth<N>"

#============================================================================
#
# The AlphaServer DS20 contains two built-in PCI SCSI adapters called PKA and
# PKB within the configuration file.
#
#----------------------------------------------------------------------------
#
# Uncomment to connect the emulator's DKA0 to the disk image.
#
#----------------------------------------------------------------------------

#set PKA container[0] = "<file-name>.vdisk"

#============================================================================
#
# Uncomment to connect the emulator's DKA100 to a host disk drive.
#
#----------------------------------------------------------------------------

#set PKA container[100] = "/dev/sd<L>"

#============================================================================
#
# Uncomment to connect the emulator's GKA200 to an unknown SCSI device.
#
#----------------------------------------------------------------------------

#set PKA container[200] = "/dev/sg<N>"

#============================================================================
#
# Uncomment to connect the emulator's DKA300 to the host's CD/DVD-ROM drive.
#
# Device name may be different depending on particular version of host
# operating system. Choose one which suits best.
#
#----------------------------------------------------------------------------

#set PKA container[300] = "/dev/cdrom"
#set PKA container[300] = "/dev/cdrom1"
#set PKA container[300] = "/dev/cdrom<N>"
#set PKA container[300] = "/dev/sr0"
#set PKA container[300] = "/dev/sr<N>"

#============================================================================
#
# Uncomment to connect the emulator's DKA400 to an .ISO file (CD/DVD image).
#
#----------------------------------------------------------------------------

#set PKA container[400] = "<file-name>.iso"

#============================================================================
#
# Uncomment to connect the emulator's MKA500 to the host's SCSI tape drive.
#
#----------------------------------------------------------------------------

#set PKA container[500] = "/dev/sg<N>"

#============================================================================
#
# Uncomment to connect the emulator's MKA600 to a .VTAPE file (tape image).
#
#----------------------------------------------------------------------------

#set PKA container[600] = "<file-name>.vtape"

#============================================================================
#
# Uncomment to connect the emulator's DKB0 to the disk image.
#
#----------------------------------------------------------------------------

#set PKB container[0] = "<file-name>.vdisk"

#============================================================================
#
# Uncomment to connect the emulator's DKB100 to a host disk drive.
#
#----------------------------------------------------------------------------

#set PKB container[100] = "/dev/sd<L>"

#============================================================================
#
# Uncomment to connect the emulator's GKB200 to an unknown SCSI device.
#
#----------------------------------------------------------------------------

#set PKB container[200] = "/dev/sg<N>"

#============================================================================
#
# Uncomment to connect the emulator's DKB300 to the host's CD/DVD-ROM drive.
#
# Device name may be different depending on particular version of host
# operating system. Choose one which suits best.
#
#----------------------------------------------------------------------------

#set PKB container[300] = "/dev/cdrom"
#set PKB container[300] = "/dev/cdrom1"
#set PKB container[300] = "/dev/cdrom<N>"
#set PKB container[300] = "/dev/sr0"
#set PKB container[300] = "/dev/sr<N>"

#============================================================================
#
# Uncomment to connect the emulator's DKB400 to an .ISO file (CD/DVD image).
#
#----------------------------------------------------------------------------

#set PKB container[400] = "<file-name>.iso"

#============================================================================
#
# Uncomment to connect the emulator's MKB500 to the host's SCSI tape drive.
#
#----------------------------------------------------------------------------

#set PKB container[500] = "/dev/sg<N>"

#============================================================================
#
# Uncomment to connect the emulator's MKB600 to a .VTAPE file (tape image).
#
#----------------------------------------------------------------------------

#set PKB container[600] = "<file-name>.vtape"

#============================================================================
#
# Uncomment to enable emulation of DEC-KGPSA-CA PCI FC Adapter.
#
#----------------------------------------------------------------------------

#load KGPSA FGA

#============================================================================
#
# Uncomment to connect the emulator's $1$DGA0 to the disk image.
#
#----------------------------------------------------------------------------

#set FGA container[0] = "<file-name>.vdisk"

#============================================================================
#
# Uncomment to connect the emulator's $1$DGA100 to a host disk drive.
#
#----------------------------------------------------------------------------

#set FGA container[100] = "/dev/sd<L>"

#============================================================================
#
# Uncomment to enable emulation of secondary DEC-KGPSA-CA PCI FC Adapter.
#
#----------------------------------------------------------------------------

#load KGPSA FGB

#============================================================================
#
# Uncomment to enable PCI Pass Through access to physical EMULEX LP FC HBA,
# use two adapters to provide multipath with failover.
#
#----------------------------------------------------------------------------

#set FGA host_bus_location = "/dev/kgpsaX"
#set FGB host_bus_location = "/dev/kgpsaY"

# this is the end of the configuration file #################################